
断胶先查温度
时间:2026-11-20 来源:http://www.jncsjx.com/ 发布人:昌盛机械
中空玻璃起雾、进水,很多时候不是玻璃原片不行,而是第一道丁基胶没涂匀。丁基胶涂布机看着简单——胶缸加热、泵挤、胶嘴吐到铝条两侧——但真跑起来,断胶、拉丝、气泡、内溢全从这台机子里冒出来。
Hollow glass fogging and water ingress often occur not because the original glass sheet is not good, but because the first layer of butyl rubber is not evenly applied. The butyl rubber coating machine looks simple - the rubber cylinder is heated, the pump is squeezed, and the rubber nozzle is sprayed onto both sides of the aluminum strip - but when it really runs, broken rubber, wire drawing, bubbles, and internal overflow all come out of this machine.
先说温度。丁基胶是热熔型,常温固态,得加热到 110–140℃ 才好挤。温度低了,熔体发稠,挤不动就断线;温度高了,胶太稀,出嘴拉丝、合片后往里爬,甚至高温裂解出微气泡,胶条表面起毛刺。 胶缸和胶嘴非常好分开控温,机头略高于缸体,升温降温都得慢慢来,别一把推到头。
Let's talk about temperature first. Butyl adhesive is a hot melt type that solidifies at room temperature and needs to be heated to 110-140 ℃ for extrusion. When the temperature drops, the melt thickens and breaks when it cannot be squeezed; The temperature is too high, the glue is too thin, and after drawing and laminating, it crawls inward, even cracking into microbubbles at high temperatures, causing burrs on the surface of the glue strip. It is best to separate the temperature control of the glue cylinder and the glue nozzle. The machine head should be slightly higher than the cylinder body, and the heating and cooling should be done slowly. Don't push the head all at once.

再看出胶量。常规铝间隔条侧面宽 5mm 左右,涂布宽度做到 4mm、两边各留 0.5mm 露白非常稳,单边胶重 3–4 g/m 是个实用参考。涂太满,预压后胶被挤进腔体内溢,Low-E 膜都给你氧化了;涂少了,拐角搭接处一有断点,水汽直接钻进去。
See the amount of glue again. The side width of the conventional aluminum spacer strip is about 5mm, and the coating width should be 4mm, with 0.5mm left on each side for the most stable white exposure. The single-sided adhesive weight of 3-4 g/m is a practical reference. The coating is too full, and after pre pressing, the adhesive is squeezed into the cavity and overflows, causing oxidation of the Low-E film; Insufficient coating, there is a breakpoint at the corner overlap, and water vapor directly seeps in.
胶嘴这块非常容易被班组忽略。残胶在嘴口碳化,出胶形状就歪,胶条带毛边。每班收工用铜片刮嘴口,严禁铁器敲;停机超 4 小时得清管路,长期停机胶缸胶头建议洗干净,不然下次开机全是黑点硬块。
The rubber nozzle is the most easily overlooked by the team. The residual glue carbonizes at the mouth, causing the shape of the glue to deviate and the glue strip to have rough edges. Scrape the mouth with copper foil at the end of each shift, and it is strictly prohibited to use iron tools to knock on it; If the machine is stopped for more than 4 hours, the pipeline must be cleaned. If the machine is stopped for a long time, the rubber head of the cylinder must be washed clean, otherwise the next time it is started, it will be full of black spots and hard blocks.
铝条本身也背锅。带油、有灰、不直、传送偏斜,胶就粘不牢,单边脱粘非常常见。涂完到合片别拖太久,30 秒内压合非常稳;低温车间(<15℃)铝条和玻璃先预热,不然胶一碰冷基材瞬间结皮,界面就是虚粘。
The aluminum strip itself also bears the blame. If there is oil, dust, unevenness, or skewed transmission, the glue will not stick firmly, and single-sided debonding is the most common. Don't delay for too long until the film is applied, the most stable compression is within 30 seconds; Preheat the aluminum bars and glass in the low-temperature workshop (<15 ℃) first, otherwise the adhesive will instantly crust when it touches the cold substrate, and the interface will be virtual adhesive.
还有个隐蔽坑:胶缸里丁基胶块和缸壁有空隙,活塞一压把空气封进胶里,隔一阵吐一串泡。装胶时分层压实、开机前排气,能省一大半气泡故障。
There is also a hidden pit: there is a gap between the butyl rubber block and the cylinder wall in the rubber cylinder, and when the piston presses, it seals the air into the rubber, causing a series of bubbles to be released every once in a while. Layered compaction during glue installation and exhaust before startup can save more than half of the bubble faults.
说白了,丁基胶涂布机不是“能出胶就行”,温度稳、量准、嘴净、条洁、压得快——这五条守住,中空玻璃的气密寿命才立得住。二道胶再贵,也救不了一道胶的断点。
To put it simply, the butyl rubber coating machine is not just about producing adhesive. Only by maintaining stable temperature, accurate measurement, clean mouth, clean strip, and fast pressure can the airtight life of insulating glass be maintained. No matter how expensive the second layer of glue is, it cannot save the breakpoint of the first layer of glue.
- 断胶先查温度 2026/11/20
- 折弯先看回弹量 2026/11/16
- 封胶线先看转角 2026/11/14
- 灌分子筛的隐形时钟 2026/11/12
- 一条线跑顺,先别只盯“全自动”三个字 2026/11/09
- 涂得准却压不上,卡在工序接缝那几秒 2026/11/06
- 胶条断在第三边,锅不一定在机器 2026/11/04
- 0.5毫米的偏差,整窗质保直接归零 2026/11/02
- 别看参数表,先看今天车间里堆的是哪种框 2026/10/30
- 中空玻璃漏不漏气,第一道胶就定了生死 2026/10/28

当前位置:



产品分类Product categories
联系我们Contact us
