折弯先看回弹量

时间:2026-11-16 来源:http://www.jncsjx.com/ 发布人:昌盛机械

全自动铝条折弯机上线,第一件事不是调速度,是先把“回弹”测准。铝条不是钢带,折完松模会回弹一点,7A/7.5A硬铝回得多,软铝回得少。程序里角度补多少,得拿实测框反推,不能信出厂默认参数。

The first thing to do when the fully automatic aluminum strip bending machine goes online is not to adjust the speed, but to first measure the "rebound" accurately. Aluminum bars are not steel strips, and after folding, the mold will rebound slightly. 7A/7.5A hard aluminum will rebound more, while soft aluminum will rebound less. The amount of angle compensation in the program needs to be calculated based on the actual measurement box, and the factory default parameters cannot be trusted.

送料段先消累计误差

The feeding section first eliminates the cumulative error

LWJ02全自动铝条折弯机

伺服送料靠同步带和夹紧轮,长期跑下来皮带松一点,尺寸就慢慢漂。每班开机先跑一根标准样条,量三段长度:

Servo feeding relies on synchronous belts and clamping wheels. After running for a long time, if the belt loosens a little, the size will slowly drift. Run a standard spline before starting each shift, and measure the length of three sections:

单边长误差超1mm,查夹紧气压和同步带张紧;

Single side length error exceeds 1mm, check the clamping pressure and synchronous belt tension;

连续多框同方向偏,查编码器零点和送料补偿值;

Continuous multiple boxes in the same direction deviation, check the encoder zero point and feed compensation value;

铝条表面有压痕,查滚轮是不是粘了铝屑或换PU包胶轮。

There are indentations on the surface of the aluminum strip. Check if the roller has adhered aluminum shavings or replace the PU coated wheel.

折角不靠“压到底”

Corner bending does not rely on "pressing to the bottom"

转角动作分两段更稳:先折到80%角度,停顿0.5秒让材料应力释放,再补到90°。硬铝、暖边复合条直接一次压死,角部容易微裂、外圆起白线。

The turning action is more stable in two stages: first fold to 80% angle, pause for 0.5 seconds to release the material stress, and then make up to 90 °. Hard aluminum and warm edge composite strips are easily crushed in one go, causing slight cracks at the corners and white lines on the outer circle.

模具V型槽宽度按铝条厚度选,常见6–8倍料厚。槽太窄铝条挤伤,太宽角不方。

The width of the V-shaped groove in the mold is selected according to the thickness of the aluminum strip, usually 6-8 times the thickness of the material. The slot is too narrow and the aluminum strip is crushed, and the angle is too wide and not square.

大框防“弹框”看辅助支撑

Large frame anti bounce frame for auxiliary support

超2米的大铝框,单边悬空折弯,重力会把相邻边带变形。大尺寸要开辅助托料,折弯顺序从长边往短边走,减少扭转。

A large aluminum frame exceeding 2 meters, with one side suspended and bent, will deform adjacent edges due to gravity. Large sizes require auxiliary material support, and the bending sequence should be from the long side to the short side to reduce twisting.

四角折完别急着松夹,先测对角线。差值超2mm,框上玻璃合片会翘,丁基胶涂布时一边厚一边薄。

Don't rush to loosen the clamp after folding the corners, measure the diagonal first. If the difference exceeds 2mm, the glass joint on the frame will warp, and the butyl rubber coating will be thicker on one side and thinner on the other.

接头和避位

Joint and avoidance

铝条续料接头、打印标识位、打孔位都在禁折区。程序里把接头避让设好,别让刀头正好落在接缝上。

The aluminum strip continuation joint, printing identification position, and punching position are all in the no folding zone. Set the joint avoidance in the program to prevent the blade from landing directly on the seam.

断料毛刺控制在可清理范围,切口斜了后续灌分子筛漏料,合片前还得二次修。

The burrs caused by material breakage should be controlled within the cleanable range. If the incision is slanted, there will be leakage during the subsequent injection of molecular sieves, and a second repair is required before laminating.

日常三件维护

Daily three maintenance items

每天清送料道和模具铝屑,划伤表面多发生在碎屑积压后;

Clean the feeding channel and mold aluminum chips every day, and scratches on the surface often occur after the debris accumulates;

气源每天排水除油,气动夹爪打滑先查滤芯;

Drain and remove oil from the air source every day. If the pneumatic gripper slips, check the filter element first;

每周校一次基准尺寸,长期连续生产微误差会累积。

Calibrate the benchmark size once a week, and long-term continuous production may accumulate minor errors.

验收跑连续50框不同规格:

Acceptance run for 50 consecutive boxes of different specifications:

量边长、对角线、角部缝隙、回弹一致性。单框漂亮不算数,换规格不重新标定点、连续跑不出稳定尺寸,才算设备真调通。

Measure side length, diagonal, corner gap, and rebound consistency. A beautiful single frame does not count. Only when the specifications are changed without re marking the point and the stable size cannot be achieved continuously, can the equipment be considered truly adjusted.

铝条折弯机不是把直条折成方框,是把“送料精度—回弹补偿—转角分阶—大框防扭—接头避让”焊进同一套参数里。参数没标实,后面合片封胶再准,框先漏气。

The aluminum strip bending machine does not fold straight strips into boxes, but welds "feeding accuracy rebound compensation corner grading large frame anti torsion joint avoidance" into the same set of parameters. The parameters are not accurate, and the sealing of the film will be done later. The frame will leak air first.

上一篇:灌分子筛的隐形时钟 下一篇:

联系我们Contact us

  • 咨询热线:0531-85717458 13705446998
  • 公司地址: 山东省德州市齐河安头乡企巢工业园
  • 扫码联系我们:

截屏,微信识别二维码

微信号:13705446998

//