0.5毫米的偏差,整窗质保直接归零

时间:2026-11-02 来源:http://www.jncsjx.com/ 发布人:昌盛机械

中空玻璃会不会起雾,很多时候不是玻璃的问题,而是铝间隔条上那圈热熔胶没打好。丁基胶是中空玻璃的第一道、也是唯一长期挡水汽的密封层,涂布机干的活看似简单:把固态胶加热到110–140℃熔融,再用稳定压力挤到铝条两侧。但“均匀、连续、不溢胶”这三条,差一条就等着售后赔单。

Whether insulating glass will fog or not is often not a problem with the glass, but rather the circle of hot melt adhesive on the aluminum spacer strip that has not been properly applied. Butyl rubber is the first and only sealing layer for insulating glass that can prevent water vapor for a long time. The job of the coating machine seems simple: heat the solid rubber to 110-140 ℃ to melt, and then squeeze it to both sides of the aluminum strip with stable pressure. But with the three principles of "uniformity, continuity, and no glue overflow", the only difference is waiting for after-sales compensation.

WJT03丁基胶涂布机(进口马达)

现场选型别被“全自动”三个字带跑,盯住三处硬指标:

Don't be misled by the words "fully automatic" when selecting on-site, focus on three hard indicators:

温控要分区——胶缸和胶嘴独立恒温,温差波动控制在1℃内。很多断胶、拉丝,根源就是胶嘴温度跟着车间气温飘。

Temperature control should be divided into zones - the glue cylinder and glue nozzle should be independently kept at a constant temperature, with temperature fluctuations controlled within 1 ℃. Many cases of broken glue and wire drawing are caused by the temperature of the glue nozzle fluctuating with the temperature in the workshop.

胶嘴间隙别凭手感——挤胶头与铝条间距比铝条宽度宽0.5mm左右非常稳,大了断胶呈圆条、小了卡框,这一刀调不好,后面合片全废。

Don't rely on the feel of the glue nozzle gap - the distance between the extrusion head and the aluminum strip is most stable when it is about 0.5mm wider than the width of the aluminum strip. If it is too large, the broken glue will form a round strip, and if it is too small, the frame will be stuck. If this knife cannot be adjusted properly, the subsequent lamination will be completely useless.

传动配伺服或变频——输送速度和出胶量建议同步,皮带一顿一顿,胶条就粗细不一;日产几百平的小厂用立式单机足够,上千平再考虑整线联动。

Transmission with servo or frequency conversion - the conveying speed and adhesive output must be synchronized, and the thickness of the adhesive strip varies with each belt stop; A small factory with a daily output of several hundred square meters is sufficient for vertical single machines, and for thousands of square meters, the whole line linkage can be considered.

两个老司机才懂的坑:停机前一定跑完管路余胶或开热吹扫,不然胶嘴一夜冷固,早上第一根铝条必堵;气源别和中空线共用一路,气压一抖,出胶就忽粗忽细。

A pitfall that only two experienced drivers understand: before stopping the machine, make sure to run off the remaining glue in the pipeline or turn on a hot blow, otherwise the glue nozzle will solidify overnight and the first aluminum strip in the morning will be blocked; Do not share the same air source with the overhead line. When the air pressure shakes, the glue will become thick and thin intermittently.

设备省两千,返修赔两万。把涂布这道工序锁死,后面的双组份封胶才扛得住年限。

Save 2000 yuan on equipment and compensate 20000 yuan for repairs. Lock the coating process in place so that the subsequent two-component sealant can withstand its lifespan.

本文由全自动丁基胶涂布机友情奉献.更多有关的知识请点击:http://www.jncsjx.com我们将会对您提出的疑问进行详细的解答,欢迎你登录网站留言.

This article is a friendly contribution from the fully automatic butyl rubber coating machine For more information, please click: http://www.jncsjx.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message

联系我们Contact us

  • 咨询热线:0531-85717458 13705446998
  • 公司地址: 山东省德州市齐河安头乡企巢工业园
  • 扫码联系我们:

截屏,微信识别二维码

微信号:13705446998

//