一条线跑顺,先别只盯“全自动”三个字

时间:2026-11-09 来源:http://www.jncsjx.com/ 发布人:昌盛机械

中空玻璃做出来容不容易起雾、漏气和边部发白,往往不是胶的问题,而是产线各段没接住。槽铝式主流工艺就五段:清洗干燥→铝框定位→合片压合→丁基胶涂布→双组份外封。

Hollow glass is less prone to fogging, air leakage, and whitening at the edges, which is often not a problem with the glue, but rather the failure of each section of the production line to catch it. The mainstream process of slot aluminum is divided into five stages: cleaning and drying → aluminum frame positioning → laminating and pressing → butyl rubber coating → two-component external sealing.

CSLBW中空玻璃板外合生产线-2

清洗段是地基:毛刷、软水、风刀、灯检缺一不可。Low-E膜面别用硬刷,水质差加软化,漂洗后表面无尘无斑,后面合片才粘得牢。

The cleaning section is the foundation: brushes, soft water, air knives, and light inspections are all indispensable. Do not use a hard brush on the surface of Low-E film. If the water quality is poor, it will soften. After rinsing, the surface will be free of dust and spots, and only then can the film be firmly bonded.

合片定位看毫米:铝框外边距玻璃边一般留2.5–3mm,定位偏差超0.5mm,压合后容易错片、封胶角部空胶。

Check the positioning of the joint in millimeters: The outer edge of the aluminum frame is generally left with a margin of 2.5-3mm from the glass edge, and the positioning deviation exceeds 0.5mm. After pressing, it is easy to make mistakes and seal the corners with empty glue.

丁基胶是防水命门:胶缸温度、胶嘴间隙、出胶压力要稳,胶条连续无断点;涂完别长时间裸放,避免表面结皮影响粘接。

Butyl rubber is the lifeblood of waterproofing: the temperature of the rubber cylinder, the gap between the rubber nozzle, and the pressure of the rubber outlet must be stable, and the rubber strip must be continuous without any breaks; After coating, do not leave it exposed for a long time to avoid surface peeling and affecting adhesion.

板压不是越重越好:按玻璃厚度和空腔设定压力,板压后空腔均匀、无滑片,再进双组份打胶。

The heavier the board pressure, the better: Set the pressure according to the thickness of the glass and the cavity. After the board pressure is applied, the cavity should be uniform and free of sliding pieces, and then apply two-component adhesive.

外封胶选对场景:门窗用聚硫或硅酮,幕墙建议硅酮;胶量、角部饱满度、无气泡,直接决定密封寿命。

Choose the right scene for external sealing adhesive: Use polysulfide or silicone for doors and windows, and silicone must be used for curtain walls; The amount of glue, fullness of corners, and absence of bubbles directly determine the sealing life.

选型先算订单结构:

Choose the order structure first:

日产百片以内、规格杂:半自动线+独立涂布机、打胶台,投入低、换型快;

Within 100 pieces per day, with various specifications: semi-automatic line+independent coating machine, glue dispensing station, low investment, fast changeover;

门窗批量单:立式全自动线,配自动上片、灯检、板压,人均效率能提一大截;

Batch order of doors and windows: vertical fully automatic line, equipped with automatic sheet loading, lamp inspection, and plate pressing, can greatly improve per capita efficiency;

要充氩气、做暖边、异形幕墙:加充气单元、分子筛自动灌装、异形合片模块,别后期硬改。

To fill argon gas, warm edges, and irregular curtain walls: add inflation units, molecular sieve automatic filling, and irregular laminating modules, do not make any hard changes later.

厂房落地前核对三件事:380V电源和0.6–0.8MPa气源、混凝土地面水平度、清洗排水和软水系统。日常维保盯毛刷磨损、水箱换水、链条张紧、胶路防固化,合片定位传感器每季度校一次。

Before landing the factory building, check three things: 380V power supply and 0.6-0.8MPa air source, concrete floor levelness, cleaning drainage and soft water system. Daily maintenance focuses on brush wear, water tank replacement, chain tension, and rubber road anti solidification. The positioning sensor is calibrated once every quarter.

找济南本地有整机自产能力的厂,优先看能否带料试机、弯通非标件同厂配套、易损件(胶嘴/密封圈/毛刷)三年供应。样机跑通再谈大货,比看宣传册稳。

Find a local factory in Jinan with the ability to produce complete machines, and prioritize whether they can provide material testing machines, non-standard bending parts, and vulnerable parts (rubber nozzles/sealing rings/brushes) for a three-year supply. Talking about bulk production after the prototype runs smoothly is more stable than reading promotional materials.

本文由中空玻璃生产线友情奉献.更多有关的知识请点击:http://www.jncsjx.com我们将会对您提出的疑问进行详细的解答,欢迎你登录网站留言.

This article is a friendly contribution from the insulating glass production line For more information, please click: http://www.jncsjx.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message

联系我们Contact us

  • 咨询热线:0531-85717458 13705446998
  • 公司地址: 山东省德州市齐河安头乡企巢工业园
  • 扫码联系我们:

截屏,微信识别二维码

微信号:13705446998

//