
胶条断在第三边,锅不一定在机器
时间:2026-11-04 来源:http://www.jncsjx.com/ 发布人:昌盛机械
中空玻璃用几年起雾,拆开常发现第一道密封胶条早有气线、缩边。问题不一定出在胶,多半出在涂布瞬间的三个变量没锁住:温度、压力、速度。
Hollow glass has been fogging up for several years, and when opened, it is often found that the first sealing strip has air lines and shrinkage edges. The problem may not necessarily lie in the adhesive, but rather in the three variables that are not locked at the moment of coating: temperature, pressure, and speed.

丁基热熔胶常温是固态,要稳定涂在铝间隔条两侧,一般熔到110–140℃。胶缸和胶嘴要分温区控制,嘴温通常比缸温高5℃左右;表显温度和实测对不上,胶条就会发毛、出气泡。
Butyl hot melt adhesive is a solid at room temperature and should be stably applied to both sides of the aluminum spacer strip, usually melting to 110-140 ℃. The rubber cylinder and nozzle should be controlled in separate temperature zones, and the nozzle temperature is usually about 5 ℃ higher than the cylinder temperature; If the displayed temperature does not match the actual measurement, the rubber strip will become fuzzy and bubble.
现场首件必查五项:
On site first article must check five items:
胶宽:关键点≥7mm,四角不断;
Glue width: key point ≥ 7mm, continuous at all four corners;
断面:切开看致密无气线,不是空心丝;
Section: Cut open to see dense and gas free lines, not hollow fibers;
粘接:压完不翘边、不粘手、不露铝;
Adhesive: no curling edges, no sticking hands, and no exposed aluminum after pressing;
两胶头间距:按铝条宽+1mm调,太宽不沾、太窄溢胶;
Distance between two adhesive heads: Adjust according to the width of the aluminum strip+1mm, too wide will not stick, too narrow will overflow adhesive;
环境适配:基材低于15℃先升温恒温30分钟,涂完30秒内压合。
Environmental adaptation: When the substrate is below 15 ℃, it should be heated and kept at a constant temperature for 30 minutes, and then pressed within 30 seconds after coating.
断胶/不匀的常见根因排序:
Common root causes of broken/uneven glue:
停机超4小时没排废,嘴口残胶碳化→先打300–500ml废胶;
Shutdown for more than 4 hours without waste discharge, residual glue at the mouth carbonized → first apply 300-500ml of waste glue;
压力不匹配线速,慢线高压挤成瘤,快线低压拉成丝→按速度重标定;
Pressure mismatch with line speed, slow line high-pressure extrusion into tumors, fast line low-pressure pulling into threads → recalibrate according to speed;
胶路有杂质堵嘴→拆头用煤油泡,别用铁器刮;
There are impurities blocking the nozzle on the rubber road. Remove the head and soak it in kerosene instead of scraping it with an iron tool;
胶本身填料多、回弹性差→手拉发脆、一拉就断。
The adhesive itself has a lot of fillers and poor resilience, making it brittle when pulled by hand and breaking easily when pulled.
选型别只看“能自动涂框”,核心看:双温区独立控温、胶量闭环、无胶报警、非常小框尺寸、换胶清洗时长。
Don't just focus on "automatic frame coating" when selecting, pay attention to: independent temperature control in dual temperature zones, closed-loop glue volume, no glue alarm, minimum frame size, and cleaning time for changing glue.
设备只是把老师傅手感变成参数。参数稳,胶条才稳;胶条稳,中空腔才不会进汽。
The equipment just turns the master's hand feel into parameters. Stable parameters make the rubber strip stable; The rubber strip is stable, so that there will be no steam entering the cavity.
- 折弯先看回弹量 2026/11/16
- 封胶线先看转角 2026/11/14
- 灌分子筛的隐形时钟 2026/11/12
- 一条线跑顺,先别只盯“全自动”三个字 2026/11/09
- 涂得准却压不上,卡在工序接缝那几秒 2026/11/06
- 胶条断在第三边,锅不一定在机器 2026/11/04
- 0.5毫米的偏差,整窗质保直接归零 2026/11/02
- 别看参数表,先看今天车间里堆的是哪种框 2026/10/30
- 中空玻璃漏不漏气,第一道胶就定了生死 2026/10/28
- 中空玻璃起雾,八成是第一道胶没涂稳 2026/10/26

当前位置:



产品分类Product categories
联系我们Contact us
