别看参数表,先看今天车间里堆的是哪种框

时间:2026-10-30 来源:http://www.jncsjx.com/ 发布人:昌盛机械

很多老板选卧式丁基胶涂布机,是被“大板、厚板、伺服精度”这几个词带跑的。机器拉回家,结果发现八成订单是1800×1500的家装窗,卧式机长长的台面大半在空转,操作工还得绕半圈取框。不是卧式不好,是订单结构和机型没对上。

Many bosses choose horizontal butyl rubber coating machines because they are influenced by the words "large plate, thick plate, servo precision". The machine was pulled home, and it was found that 80% of the orders were for 1800 × 1500 home decoration windows. The long table of the horizontal machine was mostly idling, and the operator had to go around half a circle to take the frame. It's not that the horizontal layout is not good, it's that the order structure and model are not aligned.

base64_image

简单记一条:家装门窗、阳台窗、规格集中的单子,立式或小台面卧式更划算,占地小、换规格快;幕墙大板、3米以上长框、三玻两腔,才值得上宽台面卧式,玻璃平放不变形,长铝框在皮带上走得更稳;经常接暖边条、圆弧异形框和打样单的,选带手动圆弧模式的卧式,工作台看得见胶嘴,手扶异形件跟着走就行;散单混线、今天门窗明天幕墙的厂,直接一台卧式宽台面覆盖200×300到3000×8000,不用两台机器换着开。

A simple note: For home decoration doors and windows, balcony windows, and orders with concentrated specifications, vertical or small countertop horizontal is more cost-effective, occupying less space and changing specifications quickly; A large curtain wall panel, a frame over 3 meters long, and three glass chambers are the only ones that are worthy of being placed horizontally on a wide countertop. The glass can be placed flat without deformation, and the long aluminum frame can walk more stably on the belt; For those who frequently receive warm edge strips, curved irregular frames, and sample sheets, choose a horizontal model with manual curved mode, where the glue nozzle can be seen on the workbench and the irregular parts can be followed by hand; For factories with scattered orders and mixed production lines, where doors and windows are installed today and curtain walls are installed tomorrow, a horizontal wide countertop can directly cover 200 × 300 to 3000 × 8000 without the need to switch between two machines.

卧式机真正的钱花在三处,签合同前逐条核对。第一,皮带不能是普通橡胶,LOW-E玻璃非常怕划膜,输送面建议静音同步带或覆柔性层,不然一批幕墙单做下来,膜层伤痕比胶省的那点钱多十倍。第二,胶缸要双独立恒温,北方冬天车间10℃、夏天35℃,单加热管控不住胶温,断胶和流胶会轮流来,胶缸和胶嘴分开控温、温差±1℃以内才稳。第三,胶路做大圆弧过渡再加一键洗胶,停机下班前热态洗一次管路,第二天开机直接出胶;没有这功能,每次换胶种或隔周末,光通胶嘴就要折腾半小时。

The real money for a horizontal machine is spent on three things, which need to be checked item by item before signing the contract. Firstly, the belt cannot be made of ordinary rubber. LOW-E glass is most afraid of scratching the film, and the conveying surface must be silent and synchronized with a belt or covered with a flexible layer. Otherwise, if a batch of curtain wall orders are made, the film damage will be ten times more expensive than the cost saved by rubber. Secondly, the glue cylinder needs to have dual independent constant temperature control. In the northern workshop, the temperature is 10 ℃ in winter and 35 ℃ in summer. Single heating cannot control the glue temperature, and the breakage and flow of glue will take turns. The glue cylinder and nozzle need to be controlled separately, with a temperature difference of ± 1 ℃ for stability. Thirdly, the rubber path should have a large circular arc transition and then be washed with one key glue. Before shutting down and leaving work, the pipeline should be washed once in a hot state, and the glue should be directly discharged when starting up the next day; Without this function, every time the glue type is changed or every other weekend, the Guangtong glue nozzle has to tinker for half an hour.

再记三条排产红线:铝框宽度换型后先空跑测宽再上胶,压轮时机不对会把框推歪;胶条宽度全点≥7mm、转角处不许露白,首件建议撕开看断面黑亮致密再开批量;长期停机超过4小时把胶缸余胶顶干净,别等周一早上堵头再拆嘴。

Remember three production red lines again: after changing the width of the aluminum frame, first measure the width by running it empty before applying glue. If the timing of the pressing wheel is not correct, the frame may be pushed off balance; The width of the adhesive strip should be ≥ 7mm at all points, and white should not be exposed at corners. The first piece must be torn open to see if the cross-section is black, shiny, and dense before starting the batch; If the machine is shut down for more than 4 hours, clean the remaining rubber top of the rubber cylinder. Don't wait until Monday morning to plug it before removing the nozzle.

把“订单定机型、皮带护膜层、双温控防四季、洗胶省半小时”钉在采购评审里,设备进场那天不会被车间主任追着骂。

Nail the "order type, belt protective film layer, dual temperature control for four seasons, and half an hour of glue cleaning" in the procurement review, and the equipment will not be chased and scolded by the workshop director on the day of entry.

联系我们Contact us

  • 咨询热线:0531-85717458 13705446998
  • 公司地址: 山东省德州市齐河安头乡企巢工业园
  • 扫码联系我们:

截屏,微信识别二维码

微信号:13705446998

//