1.双组份打胶机的A组、B组份胶应保持清洁,严防异物进入胶中.

1. A group and B component glue should be kept clean and prevent foreign body from entering into glue

2.全封闭固化剂胶路系统，避免固化剂与空气接触而固化

2., all closed curing agent road system, to avoid curing agent and air contact and curing

3、升降系统采用手动转阀控制,两种组份的比例调节,可通过调整滑块在摆动杆上的位置来改变.以上是双组份打胶机的基本才做原理.

3. The lifting system is controlled by manual rotary valve. The proportion adjustment of the two components can be changed by adjusting the position of the slider on the swing bar

4.节约人工：用工少，机械操控一人完全可以。

4., save labor: less labor, mechanical control, a person can solve. 

5、固化剂过滤器下端出口及混合器进料处均设有高压球阀,冲胶泄压用,混合器上设有单向针阀,不但使混胶更加均匀,而且防止两种组份互窜.

5. The lower end of the stabilizer, the outlet of the filter and the mixer inlet are all equipped with high pressure ball valve, which is used for punching, releasing and pressure. The mixer is equipped with one-way needle valve, which not only makes mixing glue more uniform, but also prevents the two components from channeling each other

6、灵敏的高压保护阀使操作和使用更

6 、 sensitive high pressure protection valve makes operation and use safer

7、基料泵、固化剂泵及比例泵均采用特殊的高压柱赛泵,双向等量供料,基料泵由液压系统驱动,固化剂泵由气动马达驱动.

7, base pump, curing agent pump and proportional pump are used special high-pressure cylinder race pump, two-way equal feeding, base pump driven by hydraulic system, curing agent pump driven by pneumatic motor

8.节省场地：双组份打胶机全套设备占地1.5×5米，可以合理的布置车间空间，有力提高车间利用率。

8., save space: two sets of glue machine, a full set of equipment covers an area of 1.5 * 5 meters, you can reasonably layout workshop space, and effectively improve the utilization rate of the workshop.

9、双组份打胶机液压/气动型主要有基料泵、固化剂泵、比例泵、基料泵升降系统、调比结构、混胶结构、气动系统、液压系统及电气系统组成.

9 、 two component rubber machine hydraulic / pneumatic type mainly has base pump, curing agent pump, proportional pump, base pump, lifting system, regulating structure, mixing structure, pneumatic system, hydraulic system and electrical system

二者辅以增压供料压盘,充分保证高黏度流体的满腔输送,基料压入并增高高压,固化剂压入并增压,再送比例泵,固化剂的流量由调比机构调节,二种组份同时送入混合器,充分混合后到达挤胶枪.

The two auxiliary booster feeding pressure plate, and fully guarantee the delivery filled with high viscosity fluid, the base material is pressed in and increased to high pressure, pressure and curing agent into the supercharger, sent to the proportional pump, curing agent flow by adjusting mechanism for adjusting the ratio of two components at the same time, into the mixer after mixing to the glue gun.

本文由双组份打胶机为您提供，我们的网站是:http://www.jncsjx.com/我们将以全心全意的热情为您提供更的服务，欢迎您的访问!

This article is made up of a two piece punch press. Our website is: http://www.jncsjx.com/We will wholeheartedly provide you with better service, you are welcome to visit!