
双组份打胶机内壁的清洁和保养
时间:2017-11-13 来源:http://www.jncsjx.com/ 发布人:昌盛机械
一、维护与保养
First, maintenance and maintenance
1、新机器经过一段时间的运转之后,双组份打胶机应多维度检查各紧固件是否有松动现象,并重新紧固。
1, after a period of operation of the new machine, should be fully checked whether the fasteners are loose, and re tightened.
2、每次使用完毕,要将机器上的残胶及灰尘清除干净,使机器保持清洁。
2, after the completion of each use, the machine to remove the residual glue and dust, so that the machine remains clean.
3、定期检查电气接线是否有松动及接地可靠性。
3. Regularly check whether the electrical wiring is loose and the reliability of grounding.

二、小型双组份打胶机机械部分的检查和保养:
Two. Inspection and maintenance of mechanical parts of small double component rubber press:
1.清洁喷枪外表、清理喷嘴,保证喷嘴的畅通;
1. clean the appearance of the spray gun and clean the nozzle to ensure the smooth flow of the nozzle;
2.清洁或更换胶机和喷枪的过滤网;
2. cleaning or changing the filter screen of glue machine and spray gun;
3.检查喷枪是否有漏胶现象,如有漏胶现象请调节,维修、更换喷枪、喷 头、喷嘴等需要更换的部件。
3. check the spray gun whether there is glue leakage phenomenon, if there is glue leakage phenomenon, please adjust, repair, replace the spray gun, nozzle, nozzle and other parts need to be replaced.
4.检查胶缸内壁是否有炭化层,如有炭化层请使用诺信专用清洗液R溶剂清洗胶缸。
4. check whether the inner wall of the cylinder has carbonized layer, if there is carbonized layer, please use the special cleaning solution R solvent cleaning cylinder.
5.将胶机加热至操作温度,排空胶箱内的热溶胶。检查胶缸内是否有杂 质,如有杂质用干净的抹布清洁胶缸。
5. the glue machine is heated to the operating temperature, the hot melt adhesive glue emptying. Check whether there is impurity in the rubber cylinder. If there is impurity, clean the rubber cylinder with clean cloth.
本文由双组份打胶机为您提供,我们的网站是:http://www.jncsjx.com我们将以全心全意的热情为您提供更优良的服务,欢迎您的访问!
In this paper, a two component glue machine to provide you, our website is: http://www.jncsjx.com, we will wholeheartedly provide you with better service, you are welcome to visit!
- 折弯先看回弹量 2026/11/16
- 封胶线先看转角 2026/11/14
- 灌分子筛的隐形时钟 2026/11/12
- 一条线跑顺,先别只盯“全自动”三个字 2026/11/09
- 涂得准却压不上,卡在工序接缝那几秒 2026/11/06
- 胶条断在第三边,锅不一定在机器 2026/11/04
- 0.5毫米的偏差,整窗质保直接归零 2026/11/02
- 别看参数表,先看今天车间里堆的是哪种框 2026/10/30
- 中空玻璃漏不漏气,第一道胶就定了生死 2026/10/28
- 中空玻璃起雾,八成是第一道胶没涂稳 2026/10/26

当前位置:



产品分类Product categories
联系我们Contact us
