
调试玻璃打胶机有那些需要注意的事项?
时间:2019-08-28 来源:http://www.jncsjx.com/ 发布人:昌盛机械
玻璃在现在的建筑中,应用越来越广泛!玻璃施工就离不开方便快捷的打胶机!下面全自动打胶机厂家就给大家普及一下,调试打胶机时有哪些都需要注意的事项!
Glass is more and more widely used in modern architecture. Glass construction is inseparable from a convenient and fast glue beater! The following full-automatic glue machine manufacturers will popularize to you, debugging glue machine when there are what need to pay attention to!
1、在当天机器操作完毕后要把胶管内的胶冲出,防止硬化;如果长时间不实用要注意用煤油清洗胶管和胶枪。
1. After the machine is finished, the glue in the rubber tube should be washed out to prevent hardening. If it is not practical for a long time, we should pay attention to cleaning the rubber tube and gun with kerosene.
2、双组份打胶机使用的硅酮胶或聚硫胶要注意杂质不能过高,低质量的胶容易堵塞胶管的过滤系统,造成出胶不畅或不均匀。
2. Silicone glue or polysulfide glue used in two-component glue beater should pay attention to the impurities should not be too high, low-quality glue is easy to block the filter system of rubber hose, resulting in poor or uneven glue production.

3、在更换胶的品种时要非常注意把双组份打胶机内残留的胶冲净,应该清洗干净,因为不同品种甚至的胶容易反应堵塞机器。
3. When replacing rubber varieties, special attention should be paid to rinsing the residual glue in the two-component glue beater, and it should be cleaned, because different kinds or even brands of glue are easy to react to clogging the machine.
4、液压站系统的压力,不能调的太高,要根据室内环境温度等实际情况,调至满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪,否则B组份管路压力将升得很高,造成安全事故。
4. The pressure of hydraulic station system can not be adjusted too high. According to the actual situation of indoor environment temperature, it can be adjusted to meet the normal tapping of rubber nozzles. When opening the hydraulic station, the rubber gun must be opened, otherwise the pressure of component B pipeline will rise very high, resulting in safety accidents.
今天就暂且和大家聊到这里,希望这篇由全自动打胶机的小编整理的知识可以帮助到您,如果您对此还有疑问,详情请咨询我们的官方。http://www.jncsjx.com
I'm going to talk to you for a moment today. I hope this article can help you. If you have any questions about it, please consult our official for details. http://www.jncsjx.com
- 折弯先看回弹量 2026/11/16
- 封胶线先看转角 2026/11/14
- 灌分子筛的隐形时钟 2026/11/12
- 一条线跑顺,先别只盯“全自动”三个字 2026/11/09
- 涂得准却压不上,卡在工序接缝那几秒 2026/11/06
- 胶条断在第三边,锅不一定在机器 2026/11/04
- 0.5毫米的偏差,整窗质保直接归零 2026/11/02
- 别看参数表,先看今天车间里堆的是哪种框 2026/10/30
- 中空玻璃漏不漏气,第一道胶就定了生死 2026/10/28
- 中空玻璃起雾,八成是第一道胶没涂稳 2026/10/26

当前位置:



产品分类Product categories
联系我们Contact us
