
自动打胶机常见问题剖析以及解决办法
时间:2019-05-06 来源:http://www.jncsjx.com/ 发布人:昌盛机械
自动打胶机可以很大程度上解放人力,同时也可以提高,下面双组份打胶机厂家就给大家普及一下自动打胶机常见问题剖析以及解决办法,希望对大家有所帮助!
Automatic gluing machine can greatly liberate human resources, but also can improve efficiency, the following two-component gluing machine manufacturers to popularize the automatic gluing machine common problems analysis and solutions, I hope to help you!
毛病1:内行走进程时或传动中止时,有玻璃渣呈现。
Faults 1: Glass slag appears when the internal walking process or transmission stops.
毛病剖析:
Analysis of defects:
(1)胶嘴的护套损坏。解决方法:换护套。
(1) The sheath of the rubber nozzle is damaged. Solution: Change the sheath.
(2)铝槽深度检测探头行走时滑到玻璃。解决方法:调理探头使其在铝槽的中心行走。
(2) Aluminum groove depth detection probe slides to glass when walking. Solution: Conditioning the probe to move in the center of the aluminium groove.
(3)挡胶板与刮胶板的行进力气太大。解决方法:调理行进气缸的速度。
(3) The driving force of the baffle and scraper is too large. Solution: Adjust the speed of the cylinder.

毛病2.机头在前移时总是把玻璃顶走
Faults 2. The nose always pushes the glass away when moving forward.
毛病剖析:
Analysis of defects:
(1)机头行进定位螺栓松动。解决方法:调理好并固定好。
(1) Loosening of heading positioning bolt. Solution: well conditioned and fixed.
(2)玻璃定位松动,使其失去效果。解决方法:调定好定位。
(2) The position of glass is loosened, which makes it ineffective. Solution: Set a good position.
(3)吸盘前后的活动量太大或吸盘的真空发生器损坏。解决方法:修理。
(3) The activity of the sucker before and after the sucker is too large or the vacuum generator of the sucker is damaged. Solution: Repair.
(4)前移气缸的行进力气太大。解决方法:调理行进速度。
(4) The forward-moving cylinder has too much driving force. Solution: Adjust the speed of travel.
毛病3.作业傍边各个动作不协调
Faults 3. Discoordination of various movements at the edge of the work
毛病剖析:
Analysis of defects:
(1)设定有误。解决方法:从头设定。
(1) The setting is wrong. Solution: Set it up from scratch.
(2)气动体系配件老化。解决方法:替换。
(2) Aging of pneumatic system fittings. Solution: Replacement.
以上精彩内容由双组份打胶机厂家整理提供,更多精彩内容欢迎大家多多关注我们的官网:http://www.jncsjx.com!多谢大家的支持。
The above wonderful content is provided by the two-component glue maker. More wonderful content is welcome to pay more attention to our official website: http://www.jncsjx.com! Thank you for your support.
- 折弯先看回弹量 2026/11/16
- 封胶线先看转角 2026/11/14
- 灌分子筛的隐形时钟 2026/11/12
- 一条线跑顺,先别只盯“全自动”三个字 2026/11/09
- 涂得准却压不上,卡在工序接缝那几秒 2026/11/06
- 胶条断在第三边,锅不一定在机器 2026/11/04
- 0.5毫米的偏差,整窗质保直接归零 2026/11/02
- 别看参数表,先看今天车间里堆的是哪种框 2026/10/30
- 中空玻璃漏不漏气,第一道胶就定了生死 2026/10/28
- 中空玻璃起雾,八成是第一道胶没涂稳 2026/10/26

当前位置:



产品分类Product categories
联系我们Contact us
