定期检查气源，应保证使用经干燥的洁净压缩空气，并定期排放分离过滤器中的积水，检查油雾器中的油是否够用。

　　Regular inspection of the gas source, first of all, should ensure the use of dry clean compressed air, and regularly discharge the water from the separation filter, check the oil mist device is sufficient oil.

　　双组份打胶机在我们平时的使用过程中有许多需要注意的事项，如果我们平时不留心注意这些地方很可能会造成我们的双组份打胶机出现各种各样的故障。这样不但影响你的生产降低你的收益还会大幅度的降低设备的寿命。

　　There are a lot of things to pay attention to in our regular use. If we don't care to pay attention to these places at ordinary times, we may cause a variety of failure of our double component glue machine. This will not only affect your production efficiency, reduce your income, but also greatly reduce the life of the equipment.

　　1、压盘上的放气阀门要保持通畅，要定期疏通和清洗。

　　1, the vent valve on the pressure plate should be kept open and regularly dredged and cleaned.

　　2、B胶桶内如果要有空气，空气将排不出来，B泵将快速往返运动，不能向高压泵内正常供胶，影响整个系统，因此，必须将空气排出来。方法是：将压盘提出从新压入并放气。

　　2, B glue barrel if there will be air, air will not come out, B pump will be fast back and forth movement, can not supply glue to the high pressure pump, affect the whole system, therefore, the air must be discharged. The method is to press the pressure plate forward and deflate.

　　3、正常工作时不要断气源，如果发现断气源应停止工作。

　　3, do not interrupt the source of gas when working normally. If you find the source of gas, you should stop working.

　　4、A胶提胶泵连续工作1分钟以上没有供胶停止，说明管路内有空气，此时会报警，须打开泵上管接头再打开A胶提胶泵，直到出胶为止，停止并接好接头，胶枪会出现有空气的哔哔爆破声，空气排净就好了。

　　4, A glue pump for more than 1 minutes for continuous work without stopping the glue, indicating the air in the pipeline, at this time the alarm will be opened, and then open the pump pipe joint and open the A glue pump, until the glue, stop and connect the joint, glue gun will appear air beep blasting sound, air clean up.

　　5、硅酮胶B 组份遇空气会结壳，影响泵的正常工作和管路的畅通，因此，停机时B组份胶的所有通道在泄压后均应关闭，使B组份不得接触空气。

　　5, silicone rubber B components in the air will shell, affect the normal work of the pump and the smooth line of the pipeline, so, when the shutdown of all B component glue after the pressure should be closed, so that the B components must not contact the air.

　　以上便是双组份打胶机今天的分享，您还满意吗，欢迎关注我们的网站：http://linshi.jncsjx.com并且关注我们的产品，我们将为您提供优良的产品，衷心的愿与您建立合作关系。

　　The above is the sharing of double component glue machine today, are you satisfied, welcome to our website: http://linshi.jncsjx.com and pay attention to our products, we will provide you with excellent products and sincerely wish to establish a cooperative relationship with you.