双组份打胶机是生产中空、幕墙玻璃的专用设备，可一次完成二道密封中A、B组份混合与涂胶。适用配比精度高的胶种，满足玻璃深加工企业率、高合格率流水线作业的生产需求，是大规模生产高档中空玻璃及玻璃幕墙产品的一种理想的配套设备。那么我们在使用的时候应该注意哪些问题？
The two-component gluing machine is a special equipment for the production of hollow and curtain wall glass. It can complete the mixing and gluing of a and B components in the secondary seal at one time. It is an ideal matching equipment for large-scale production of high-quality insulating glass and glass curtain wall products. So what problems should we pay attention to when using it?
1.由于双组份密封胶的固化需要一定时间，因此，已涂了双组份密封胶的玻璃应水平轻轻搬动。
1. As the curing of the two-component sealant takes a certain time, the glass coated with the two-component sealant should be moved horizontally and gently.
2.A组、B组份胶应保持清洁，严防异物进入胶中。
2. The glue of group A and component B should be kept clean, and foreign matters should be strictly prevented from entering the glue.

3.在连续工作过程中，胶枪每次停止工作时间一般不得超过20分钟，否则，应用A组份胶冲出全部混合胶，直单一的A组份胶从枪口排出为止。
3. In the process of continuous operation, the stop time of glue gun should not exceed 20 minutes each time. Otherwise, all the mixed glue should be flushed out with component a until the single component a glue is discharged from the muzzle.
4.高压胶管不得强行挤压、弯曲，防止影响系统正常工作。
4. The high pressure hose shall not be forced to squeeze or bend to prevent the normal operation of the system.
5.混胶器应经常保持畅通，以保证良好的出胶效果。如遇堵塞情况，可用丙酮浸泡后清洗。建议每5组清洗一次。
5. The mixer should always be kept smooth to ensure good glue output. In case of blockage, it can be cleaned after soaking in acetone. It is recommended to clean every 5 groups.
6.当胶枪长时间不用时（超过一周），应拆下枪体使用溶剂将胶枪和混胶器内的残留胶体清洗干净。
6. When the glue gun is not used for a long time (more than a week), the gun body should be removed and the residual colloid in the glue gun and the glue mixer should be cleaned with solvent.
7.不同双组份胶生产厂家所生产的胶内含杂质数量不同，根据实际情况清晰B组分的过滤网及单向止回阀，建议每两组清洗一次。
7. The amount of impurities in the rubber produced by different two-component rubber manufacturers is different. According to the actual situation, the filter screen and one-way check valve of component B should be clear. It is recommended to clean every two groups.
8.任何因胶体固化所造成的胶枪、管路或整机的故障，一律不在保修范围之内。
8. Any failure of glue gun, pipeline or whole machine caused by colloid solidification is not covered by warranty.
9.定期给各泵的加油口加油，应保证油雾器内不断油。
9. Add oil to the oil filler of each pump regularly, and ensure that there is no oil in the atomizer.