中空玻璃生产线的使用寿命一般取决于中空玻璃生产线的清洗段和板压段，那么，如何保养好中空玻璃生产线的清洗段和板压段，就关系到整套中空玻璃设备的使用寿命，威力智能为您分享中空玻璃生产线的清洗段和板压段如何保养：

The service life of a hollow glass production line generally depends on the cleaning section and plate pressing section of the hollow glass production line. Therefore, how to maintain the cleaning section and plate pressing section of the hollow glass production line is related to the service life of the entire set of hollow glass equipment. Power Intelligence will share with you how to maintain the cleaning section and plate pressing section of the hollow glass production line:

中空玻璃生产线清洗干燥段

Cleaning and drying section of insulated glass production line

中空玻璃生产线清洗机现在大多数厂家用的是不锈钢，一般不会生锈,那重 点就是毛刷和电机的保养了，毛刷一般能用能长期使用，如果不脱 毛可以一直使用，只是他的下端轴承，因为湿度大容易生锈，造成毛刷锈住、抱死或阻力大等故障，还容易烧掉电机。威力智能提供的中空玻璃生产线的毛刷都是采用进口杜邦丝，清洗效果好， 不易脱 毛，可以长时间使用；而且去掉了海绵辊，既保证了玻璃不会二次污染，采用高压风机循环热风，保证吹干效果；再就是下端采用纯钢甚纯铜轴承，大限度的隔绝生锈造成损失等情况的发生。

Most manufacturers now use stainless steel as the cleaning machine for insulated glass production lines, which generally does not rust. The key is to maintain the brush and motor. The brush can generally be used for a long time, and if it does not shed hair, it can be used for a long time. However, its lower bearing is prone to rust due to high humidity, causing problems such as the brush rusting, locking, or resistance, and easily burning the motor. The brushes on the insulated glass production line provided by Power Intelligence are all made of imported DuPont silk, which has a good cleaning effect and is not easy to remove hair, and can be used for a long time; Moreover, the sponge roller has been removed, ensuring that the glass will not be contaminated again. A high-pressure fan is used to circulate hot air, ensuring the drying effect; Another issue is the use of pure steel or even pure copper bearings at the lower end, which greatly isolates losses caused by rust.

中空玻璃生产线板压段

Hollow glass production line board pressing section

再就是板压机，特别是中空玻璃生产线内合片的板压机有很多气缸和电磁阀，如果不注意保养、加油、排水，很容易卡阀或烧线圈，特别是吸盘上的电磁阀不可以在油水分离器里加油润滑，因为那样会造成吸盘上也有油，污染玻璃。所以只能拔下电磁阀的进气管用油壶加一点润滑油。

Another issue is the plate press machine, especially the plate press machine for laminating in the hollow glass production line, which has many cylinders and solenoid valves. If maintenance, oiling, and drainage are not taken seriously, it is easy for the valve to get stuck or the coil to burn. Especially for the solenoid valve on the suction cup, it cannot be lubricated in the oil-water separator because it will also cause oil on the suction cup, polluting the glass. So you can only unplug the intake pipe of the solenoid valve and add some lubricating oil with an oil pot.

还有就是，丁基胶涂布机，也是需要注意保养的，在冷胶状态不能退缸，因为冷胶状态下胶和活塞是粘在一起的，如果强退，很容易把胶缸拔坏；再就是加胶时一定检查好胶块的外观有没有粘有铁销、小石块和铁钉等杂物，这些东西是很容易划伤胶缸或堵住胶头的。

Also, the butyl adhesive coating machine also needs to be maintained carefully. In the cold adhesive state, the cylinder cannot be removed because the adhesive and piston are stuck together in the cold adhesive state. If removed forcefully, it is easy to damage the adhesive cylinder; Furthermore, when adding glue, be sure to check the appearance of the glue block for any foreign objects such as iron pins, small stones, and nails, which can easily scratch the glue cylinder or block the glue head.