
丁基胶涂布机的压轮力度怎么调整?
时间:2023-11-20 来源:http://www.jncsjx.com/ 发布人:昌盛机械
转动皮带传送开关,使其处于“开”位置,观察皮带是否有跑偏现象,并调整涨紧螺栓,使其校正。
Turn the belt conveyor switch to the "on" position, observe if the belt is running off, and adjust the tension bolt to make it correct.
开机前,依据间隔框宽度,松开打胶头紧定螺栓,调整两挤胶头的间隔距离,调整时,要使框的对称中心、两个小压轮宽度的对称中心、两打胶头的对称中心重合(此项只有在间隔框宽度改变时进行调整),调整完毕紧固螺钉。
Before starting the machine, loosen the fixing bolts of the glue head according to the width of the spacing box, adjust the spacing distance between the two glue heads. When adjusting, make sure that the symmetrical center of the box, the symmetrical center of the width of the two small pressure wheels, and the symmetrical center of the two glue heads coincide (this item can only be adjusted when the width of the spacing box changes). After adjusting, tighten the screws.


工作前温度调节: 因各厂家生产丁基胶规定的加热温度及工艺参数不同,所以设定打胶座温度一般为120-140度,胶缸温度为110-120度(此值仅作参考),待加热温度达到设定值15-30分钟后,方可打胶。
Temperature adjustment before work: Due to the different heating temperatures and process parameters specified by various manufacturers for producing butyl rubber, the temperature of the glue holder is generally set at 120-140 degrees, and the temperature of the glue cylinder is set at 110-120 degrees (this value is only for reference). The glue can only be applied after the heating temperature reaches the set value of 15-30 minutes.
本文由中空玻璃丁基胶涂布机友情奉献.更多有关的知识请点击:http://www.jncsjx.com真诚的态度.为您提供为多维度的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.
This article is dedicated by the insulated glass butyl adhesive coating machine. For more relevant knowledge, please click on: http://www.jncsjx.com Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned
上一篇:卧式中空玻璃设备的组成及使用注意要点
下一篇:中空玻璃生产线的清洗段和板压段的保养
相关新闻 more+
- 折弯先看回弹量 2026/11/16
- 封胶线先看转角 2026/11/14
- 灌分子筛的隐形时钟 2026/11/12
- 一条线跑顺,先别只盯“全自动”三个字 2026/11/09
- 涂得准却压不上,卡在工序接缝那几秒 2026/11/06
- 胶条断在第三边,锅不一定在机器 2026/11/04
- 0.5毫米的偏差,整窗质保直接归零 2026/11/02
- 别看参数表,先看今天车间里堆的是哪种框 2026/10/30
- 中空玻璃漏不漏气,第一道胶就定了生死 2026/10/28
- 中空玻璃起雾,八成是第一道胶没涂稳 2026/10/26

当前位置:



产品分类Product categories
联系我们Contact us
