Lubricate both electric motors. The main motor and auxiliary motor of the butyl rubber applicator are equipped with lubricators at the inlet.

当机油低于低端刻线时，应将机油杯取下并重新加注10号机油。 如果没有注油器，则在滴油或电动机严重缺油时，可以拆下主电动机进气管和电动机之间的带电连接，并应使用油枪补充油，并使用辅助电动机 可以旋开端盖螺母以加油。

When the oil level drops below the low end mark, the oil cup should be removed and refilled with No. 10 oil. If there is no oil injector, the live connection between the main motor intake pipe and the motor can be removed in case of oil dripping or severe oil shortage in the motor. An oil gun should be used to replenish the oil, and an auxiliary motor can be used to loosen the end cap nut for refueling.

2.丁基胶打胶机使用一段时间后，主泵，辅助泵和比例泵会从内部泄漏胶水，并流入油杯。 您可以清洁胶水并添加油。 用十字螺丝刀固定住主泵，将两个泵油碗的下端的圆孔顺时针拧紧。 配套的油杯可用扳手拧紧。

2. After using the butyl glue applicator for a period of time, the main pump, auxiliary pump, and proportional pump will leak glue from inside and flow into the oil cup. You can clean the glue and add oil. Fix the main pump with a cross screwdriver and tighten the circular holes at the lower ends of the two pump oil bowls clockwise. The matching oil cup can be tightened with a wrench.

3.用油枪将阀注满阀的小孔，以防生锈。

3. Fill the small hole of the safety valve with an oil gun to prevent rusting.

4. Y型过滤器位于辅助泵的出口。 清洁时，拧开端盖，将其浸入煤油中，然后用牙刷清洁。 安装时，将网罩放到端盖中并拧到底，然后用扳手拧紧。 用一套胶水清洗一次，如果没有杂质，用两套胶水清洗，控制灵活。

4. The Y-shaped filter is located at the outlet of the auxiliary pump. When cleaning, unscrew the end cap, immerse it in kerosene, and then clean it with a toothbrush. When installing, place the mesh cover in the end cover and tighten it to the bottom, then tighten it with a wrench. Clean once with one set of glue, and if there are no impurities, clean with two sets of glue for flexible control.

5.大型过滤器的位置在高压仪表B台的右下角，拧下回油阀下方的软管，拧下过滤器，取出网和芯，弹簧，取出，用刷子清洗， 并用凸块上的芯覆盖弹簧的小孔。 向后旋转，然后将其拧紧在丁基胶打胶机上。

5. The position of the large filter is in the lower right corner of the high-pressure instrument panel B. Unscrew the hose below the return valve, unscrew the filter, take out the mesh, core, spring, remove it, clean it with a brush, and cover the small hole of the spring with the core on the convex block. Rotate it backwards and then tighten it onto the butyl adhesive applicator.

3-5组洗一次。 如果没有杂质，则可以灵活控制。

Wash once in 3-5 groups. If there are no impurities, it can be flexibly controlled.

本文由立式丁基胶涂布机整理发布，您是不是对这些内容有所了解了呢?更多的内容请点击：http://www.jncsjx.com我们会有更多精彩内容等你查看。

This article is organized and published by a vertical butyl adhesive coating machine. Do you have any understanding of these contents? For more information, please click on: http://www.jncsjx.com We will have more exciting content waiting for you to check out.