双组份打胶机的操作过程十分的简单，小编大概总结下分为两个部分一个是控制系统的操作，另一个就是胶桶的安装/更换，具体点的方法如下。
The operation process of the two-component gluing machine is very simple. It can be divided into two parts. One is the operation of the control system, and the other is the installation / replacement of the glue barrel. The specific methods are as follows.
①控制系统操作方法
① Operation method of control system
1.接通电源（380V 三相四线）和气源（0.6-0.7MPa）。
1. Connect the power supply (380V three-phase four wire) and air source (0.6-0.7mpa).
2.打开A,B胶供胶阀门，关闭B胶回流阀门。
2. Open the glue supply valve of a and B glue and close the glue return valve of B glue.

3.在控制面板上选择“开机”然后检查一下A,B胶是否工作正常。此时供胶机混胶工作准备就绪。
3. Select "power on" on the control panel and check whether glue a and B work normally. At this time, the mixing work of the glue feeder is ready.
4、如果长时间不用（超过15分钟）或者是下班时要在控制面板上选择“冲枪”，然后打开B胶回流阀门，关闭B胶供胶阀门.此时供胶机冲枪准备工作就绪。
4. If you don't use it for a long time (more than 15 minutes) or when you are off duty, you should select "flushing gun" on the control panel, then open the B glue return valve and close the B glue supply valve. At this time, the flushing gun of the glue feeder is ready.
5、每次操作前确保设备的水平度，调整机器的水平度，调节地脚的高度使机身水平。
5. Before each operation, ensure the levelness of the equipment, adjust the levelness of the machine, and adjust the height of the foundation to make the fuselage level.
6、接通电源后先检查各电机的旋转方向是否正确，接通与CL—A—01打胶机的胶管、信号。（注意：A胶提胶齿轮泵电机的旋转方向必须符合齿轮泵旋转方向）
6. After the power is turned on, check whether the rotation direction of each motor is correct, and connect the hose and signal of cl-a-01 glue machine. (Note: the rotation direction of a glue lifting gear pump motor must conform to the rotation direction of gear pump)
②胶桶的安装/更换
② Installation / replacement of rubber barrel
1、在控制面板上选择“AB胶压盘”。
1. Select "AB glue pressure plate" on the control panel.
2、再选择“A胶升”此时A胶压盘上升。
2. Then select "a glue up" and the a glue pressure plate will rise.
3、高度到位时在控制面板上选择“A胶停”
3. When the height is in place, select "a glue stop" on the control panel
4、将A胶桶放到压盘下面，打开桶盖将里面的胶袋固定好，将胶桶的上口与压盘对齐（注意：新机器或是刚换上的密封圈是要先将密封圈外表涂上A胶，以便起到润滑作用）。
4. Put a rubber barrel under the pressure plate, open the lid of the barrel, fix the inner plastic bag, and align the upper opening of the rubber barrel with the pressure plate (Note: for new machine or newly replaced sealing ring, first coat a rubber on the surface of the sealing ring, so as to play a lubricating role).
5、打开A胶压盘上的排气阀，然后再选择“A胶降”，此时A胶压盘下降，等压盘快要降到桶口时停止下降，检查压盘是否对齐桶口，调整胶桶的位置对齐为止。
5. Open the exhaust valve on the pressure plate of glue a, and then select "glue a drop". At this time, the pressure plate of glue a will drop. Stop falling when the pressure plate is about to drop to the mouth of the barrel. Check whether the pressure plate is aligned with the mouth of the barrel, and adjust the position of the barrel until it is aligned.
6、让压盘断续下降（即A胶降→A胶停→A胶降---），当压盘压入桶内时可使压盘连续下降，此时排气阀内有空气排出，当排气阀内连续排出A胶而没有空气排出时，压盘停止下降并关闭阀门。
6. Let the pressure plate drop intermittently (i.e. a glue drop → a glue stop → a glue drop -). When the pressure plate is pressed into the barrel, it can make the pressure plate drop continuously. At this time, air is discharged from the exhaust valve. When a glue is continuously discharged from the exhaust valve but no air is discharged, the pressure plate stops falling and the valve is closed.
7、此时A桶安装完成，达到工作准备状态。B胶桶安装方法同A胶安装方法。
7. At this time, the installation of barrel a is completed and the work is ready. The installation method of B glue barrel is the same as that of a glue barrel.