双组份打胶机旋转伺服报警810？这样解决快速恢复生产

　　Dual component glue machine rotation servo alarm 810? This is how to quickly restore production

　　在中空玻璃生产中，双组份打胶机是保障密封性能的核心设备，而旋转伺服系统则是控制机头精准旋转、保证打胶轨迹规整的关键部件。不少一线操作人员都遇到过这样的困扰：打胶机机头旋转伺服驱动器突然报警，屏幕显示代码810，设备直接停摆，严重耽误生产进度。其实这个报警故障大多是伺服系统出现瞬时异常导致的，不用找专业维修人员，自己按步骤操作就能大概率解决。今天就专门科普双组份打胶机的实用故障排查技巧，详细说说旋转伺服报警810的解决方法。

　　In the production of insulating glass, the two-component gluing machine is the core equipment to ensure sealing performance, and the rotary servo system is the key component to control the precise rotation of the machine head and ensure the regular gluing trajectory. Many frontline operators have encountered this problem: the servo drive of the glue machine head suddenly alarms, the screen displays code 810, and the equipment stops directly, seriously delaying production progress. In fact, most of the alarm faults are caused by instantaneous abnormalities in the servo system, and there is no need to seek professional maintenance personnel. You can most likely solve them by following the steps yourself. Today, we will specifically explain the practical troubleshooting techniques for two-component gluing machines, and provide a detailed solution for the rotation servo alarm 810.

　　先跟大家简单说明一下，旋转伺服报警810大多和系统信号异常、瞬时负载波动有关，属于常见的可复位故障，不是设备核心部件损坏，所以不用过度焦虑。解决这个故障的核心思路很简单：先通过设备系统进行旋转电机复位操作，若复位成功，再通过断电重启稳定系统状态；若仍有报警，重复复位流程即可。整个过程不用拆解设备、不用复杂工具，新手也能快速上手。

　　Let me briefly explain that the rotation servo alarm 810 is mostly related to system signal abnormalities and instantaneous load fluctuations, and is a common resettable fault. It is not a damage to the core components of the equipment, so there is no need to be overly anxious. The core idea for solving this fault is simple: first, reset the rotating motor through the device system. If the reset is successful, then stabilize the system state by shutting down and restarting; If there is still an alarm, repeat the reset process. The entire process does not require dismantling equipment or complex tools, and beginners can quickly get started.

　　第一步，系统内执行旋转电机复位。首先找到打胶机的操作屏幕，在屏幕上找到“报警列表”选项并点开，在报警列表中定位到“旋转电机复位”功能按钮。接下来按规范操作：用手指长按“旋转电机复位”按钮，保持5秒钟后再松开；松开后不要急着下一步，再次长按“旋转电机复位”按钮，直到屏幕上显示“复位成功”的提示，这一步复位操作就完成了。这里要注意，长按时间一定要够，没显示成功前不要随意松开，否则复位无效。

　　The first step is to reset the rotating motor within the system. Firstly, locate the operation screen of the glue machine, find the "Alarm List" option on the screen and click on it. In the alarm list, locate the "Rotary Motor Reset" function button. Next, follow the standard procedure: press and hold the "Rotary Motor Reset" button with your fingers for 5 seconds before releasing it; After releasing, do not rush to the next step. Press and hold the "Rotary Motor Reset" button again until the screen displays the prompt "Reset Successful". This reset operation is complete. Please note that the long press time must be sufficient, and do not release it casually until it displays successfully, otherwise the reset will be invalid.

　　第二步，断电重启稳定系统。完成复位操作后，需要通过断电重启来进一步稳定伺服系统状态。操作步骤很简单：先找到设备的电源钥匙开关，将钥匙拧至关闭位置，实现设备断电；等待1-2分钟，让系统完全放电后，再将钥匙拧回开启位置，重新启动设备。设备开机后，不要立即进行打胶作业，先空载测试一下机头旋转功能，观察是否还有报警提示。

　　Step 2: Power off and restart the stable system. After completing the reset operation, it is necessary to power off and restart to further stabilize the servo system state. The operation steps are simple: first find the power key switch of the device, turn the key to the off position, and power off the device; Wait for 1-2 minutes to fully discharge the system, then turn the key back to the open position and restart the device. After the device is turned on, do not immediately perform gluing operations. First, test the rotation function of the machine head with no load and observe if there are any alarm prompts.

　　第三步，重复操作应对反复报警。如果重启开机后，旋转伺服仍然报警810，不用着急。这种情况大概率是系统异常信号没有完全清除，此时可以重复第一步和第二步的操作流程——再次执行旋转电机复位（确保显示成功），然后再次断电重启。通常情况下，重复2-3次后，报警就能彻底消除，设备恢复正常。如果重复多次后仍有报警，再考虑联系设备厂家排查是否存在硬件接触不良等问题。

　　Step three, repeat the operation to deal with repeated alarms. If the rotary servo still alarms 810 after restarting the machine, there is no need to worry. This situation is most likely due to the system's abnormal signal not being completely cleared. In this case, you can repeat the first and second steps of the operation process - perform the rotating motor reset again (ensure successful display), and then power off and restart again. Normally, after repeating 2-3 times, the alarm can be completely eliminated and the equipment can return to normal. If there is still an alarm after repeated attempts, consider contacting the equipment manufacturer to investigate whether there are hardware contact issues.

　　这里给大家补充几个实操注意事项：一是操作过程中要注意安全，断电重启前确保周围没有人员接触设备运动部件，避免开机后意外受伤；二是复位时一定要紧盯屏幕提示，只有明确显示“成功”才算有效，没成功就重新操作；三是日常使用中，建议避免频繁启停设备、粗暴操作机头旋转，减少伺服系统的瞬时负载波动，能有效减少这类报警的发生。另外，每次出现报警后，最好简单记录一下操作时间和解决过程，方便后续总结规律。

　　Here are a few practical precautions for everyone: First, pay attention to safety during the operation process. Before turning off the power and restarting, ensure that there are no people around who come into contact with the moving parts of the equipment to avoid accidental injury after turning on the machine; Secondly, when resetting, be sure to pay close attention to the screen prompt. Only when it clearly displays "successful" can it be considered effective. If it is not successful, restart the operation; Thirdly, in daily use, it is recommended to avoid frequent starting and stopping of equipment, rough operation of the machine head rotation, and reduce the instantaneous load fluctuation of the servo system, which can effectively reduce the occurrence of such alarms. In addition, it is best to briefly record the operation time and resolution process after each alarm occurs, in order to facilitate the subsequent summary of patterns.

　　对中空玻璃生产企业来说，双组份打胶机的稳定运行直接关系到生产效率和产品质量。像旋转伺服报警810这样的常见故障，掌握简单的复位和重启技巧就能快速解决，不用耽误太多生产时间。一线操作人员多掌握这类基础故障排查技巧，能大幅提升应对突发问题的能力，降低对专业维修的依赖。希望这次科普能帮到大家，在日常操作中更好地应对双组份打胶机的各类小故障，让生产更顺畅。如果遇到其他复杂报警，也可以先查看设备说明书，或及时联系厂家技术支持。

　　For insulated glass production enterprises, the stable operation of two-component gluing machines is directly related to production efficiency and product quality. Common faults such as the rotary servo alarm 810 can be quickly resolved by mastering simple reset and restart techniques, without wasting too much production time. Front line operators who have mastered these basic troubleshooting skills can greatly enhance their ability to deal with unexpected problems and reduce their dependence on professional maintenance. I hope this science popularization can help everyone better deal with various minor faults of two-component gluing machines in daily operation, making production smoother. If encountering other complex alarms, you can also check the equipment manual first or contact the manufacturer's technical support in a timely manner.

　　本文由  双组份打胶机 友情奉献.更多有关的知识请点击  http://www.jncsjx.com/   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from a two-component glue machine For more related knowledge, please click http://www.jncsjx.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.