中空玻璃打胶机不出胶的原因及解决方法：
Reasons and solutions for failure of insulating glass gluing machine:
1、检查气源是否在0.6～0.8Mpa之间；
1. Check whether the air source is between 0.6 and 0.8MPa;
2、在触摸屏的编辑功能菜单中检查印章是否未使用；
2. Check whether the seal is not used in the editing function menu of the touch screen;
3、检查气动开关是否被挡住；
3. Check whether the pneumatic switch is blocked;
4、检查黑胶气动开关和电磁阀动作是否正常；
4. Check whether the black glue pneumatic switch and solenoid valve operate normally;
5、检查比例泵上的智能压力表是否报警，范围7-35Mpa；
5. Check whether the intelligent pressure gauge on the proportional pump gives an alarm, with the range of 7-35mpa;
6、检查液压站内是否有压力，若无压力：
6. Check whether there is pressure in the hydraulic station. If there is no pressure:
1）清洗比例溢流阀
1) Cleaning proportional overflow valve
2）检查比例控制器是否通电或松动；
2) Check whether the proportional controller is powered on or loose;
7、清洗时白胶是否可以释放，如果不能，检查313软管和旋转接头是否堵塞；
7. Whether the white glue can be released during cleaning. If not, check whether 313 hose and rotary joint are blocked;
8、检查一组比例泵下限传感器IB233是否有信号，检查二组比例泵是否有信号；
8. Check whether there is a signal from the lower limit sensor ib233 of the first group of proportional pumps and whether there is a signal from the second group of proportional pumps;
9、手动检查中空玻璃打胶机的扫描数值是否正常。
9. Manually check whether the scanning value of insulating glass gluing machine is normal.
当双组份胶在混合过程中发生局部固化时，打胶机打出来的胶就会出现结皮或硫化现象。出现这一现象的原因主要有三种：
When the two-component rubber is partially cured in the mixing process, the rubber produced by the beater will appear skinning or vulcanization. There are three main reasons for this phenomenon:

⑴胶体颜色较黑，固化快时，可能是由于B组分比例过高，过多的催化剂促使固化速度更快。此时，需要适当降低B组分的比例，将结皮或硫化胶冲洗干净后施工；
(1) when the colloid color is black and the curing speed is fast, it may be due to the high proportion of component B and too much catalyst. At this time, it is necessary to properly reduce the proportion of component B and wash the crust or vulcanizate before construction;
⑵打胶机若打胶过程中伴有出胶慢的现象时，可能是混合芯长时间未清洗或清洗不完全，胶体结皮堵塞管道。因此，定期清洗静态混合器是很有必要的。
(2) if the gluing machine is accompanied by slow glue output during gluing, it may be that the mixing core has not been cleaned for a long time or is not completely cleaned, and the colloid crust blocks the pipeline. Therefore, it is necessary to clean the static mixer regularly.
⑶当固化和出胶速度均无异常，而打出的胶仍有结皮或硫化现象时，则可能是设备停机时间较长，胶枪未清洗或洗枪不够干净，需要将结皮或硫化胶冲洗干净后后施工。
(3) when there is no abnormality in the curing and glue outlet speed, but there is still peeling or vulcanization of the punched glue, it may be that the equipment has been shut down for a long time, the glue gun is not cleaned or the cleaning gun is not clean enough. It is necessary to wash the peeling or vulcanization before construction.
以上就是为大家介绍的有关双组份打胶机的详细介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://linshi.jncsjx.com
The above is a detailed introduction to the two-component gluing machine. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://linshi.jncsjx.com