双组份打胶机呈现花胶的问题无论是进口的立式打胶机仍是卧式打胶机都会经常呈现的一种毛病，双组份打胶机一般呈现花胶这种毛病大多是由以下几个原因导致的。
The two-component gluing machine presents the problem of flower glue, which is often found in both imported vertical and horizontal gluing machines. The problems of two-component gluing machines are mostly caused by the following reasons.
1、双组份打胶机的混胶器内胶体过多固话，阻力增大。
1. There are too many colloids in the mixer of the two-component dispenser, and the resistance increases.
2、A或B胶胶桶内无胶，胶已用完。
2. There is no glue in a or B glue barrel, and the glue has been used up.
3、A或B胶胶桶内有空气。
3. There is air in rubber barrel a or B.
4、针阀或单向阀阻塞。咱们仔细观察小编所写的导致花胶的毛病原因会发现大多是因为设备没有定时保护清洗导致的。所以咱们一定要牢记设备一定要定时保护清洗的良好习惯。
4. The needle valve or check valve is blocked. If we carefully observe the reasons for the problems of the glue, we will find that most of them are caused by the equipment is not regularly protected and cleaned. So we must keep in mind that the equipment must be regularly protected and cleaned.

一种状况是因为咱们将打胶机的打胶速度设置的过快导致的。有的客户为了加速自己的生产节奏追逐生产计划，将打胶速度以为调整的过快，导致胶体还没有彻底达到合格标准机头就已经移动到下一个位置进行打胶操作了.
One is because we set the glue speed of the glue machine too fast. In order to speed up their own production rhythm and pursue the production plan, some customers think that the gluing speed is adjusted too fast, resulting in the glue has not completely reached the qualified standard, the machine head has moved to the next position for glue operation
假如咱们需要加速打胶的速度调整了打胶机的移动参数的话，那么咱们对应的也应该对供胶体系也进行相应的设置，比方这时候咱们就需要加大供胶压力，增大打胶机的出胶速度来配合目标的移动速度的增加。
If we need to speed up the gluing speed and adjust the moving parameters of the gluing machine, then we should also set the corresponding glue supply system. For example, at this time, we need to increase the glue supply pressure and the glue output speed of the gluing machine to match the increase of the moving speed of the target.
假如咱们仅仅是独自的增加了打胶机的移动速度而没有对压力进行调理的话就很有可能呈现打胶不丰满的状况发生。另外一种状况跟打胶机的速度差不多便是咱们的供胶压力不足导致的。
If we only increase the moving speed of the gluing machine alone and do not regulate the pressure, it is likely that the glue is not full. Another situation is that the speed of the glue machine is almost the same, which is caused by the insufficient glue supply pressure.
双组份打胶机产生打胶不丰满的原因可以参考种状况。除了以上小编说的人为原因导致的这个毛病以外设备的零部件损坏也会导致这个问题，比方机头感应器损坏。
The reason of the two-component gluing machine is not full can refer to the situation. In addition to the above small series of human causes of this problem, equipment parts damage will also lead to this problem, such as head sensor damage.