中空玻璃自动打胶机的操作调试要注意什么?
时间:2023-11-20 来源:http://www.jncsjx.com/ 发布人:昌盛机械
打开气泵开关,电源总开关,控制台开关,在控制台按手动按钮,然后在显示屏上找到原点设定,点击辅助原点设定,然后点击头部原点设定,注意原点设定时避免头部和辅助吸盘碰撞。等设定好然后返回找到玻璃厚度设定,先是玻璃的厚度然后是铝隔条然后还是玻璃的厚度,输入完以后,点击设置进入。等命令位置和当前位置数值一致即可,注意设置时传送带上不要有玻璃。
Turn on the air pump switch, main power switch, and console switch. Press the manual button on the console, then find the origin setting on the display screen, click on the auxiliary origin setting, and then click on the head origin setting. Pay attention to avoiding collisions between the head and the auxiliary suction cup when setting the origin. Wait for the settings to be completed and then return to find the glass thickness settings. First, the thickness of the glass, then the aluminum spacer, and then the thickness of the glass. After entering, click on the settings to enter. Wait until the command position matches the current position value, and be careful not to have glass on the conveyor belt during setting.
然后是混交了,按第一桶胶按钮,按工作选择按钮,然后按拍胶启动,在按伐开,此时胶头以出胶,等看不见白胶,以混均匀以后按伐关,在按链接生产线,自动,自动运行,此时可以自动打胶。
Then there is mixing, press the first barrel glue button, press the work selection button, and then press the tapping glue to start. At this time, the glue head will release the glue. When the white glue is not visible, mix evenly and then press the tapping off button. Press the link to the production line, and the automatic and automatic operation will start. At this time, the glue can be automatically applied.
开始打胶要看每条边每个角打胶是否均匀,下面说下如何调整打胶机,在屏幕上点击返回找到密封配方,点击进入,会显示当前密封压力,如果每条边都缺胶,那么可增加压力,压力大胶量大,压力小胶量就小。
To start gluing, it is necessary to check whether the gluing is evenly applied on each edge and corner. Below is how to adjust the gluing machine. Click on the screen to return and find the sealing formula. Click on the enter button to display the current sealing pressure. If each edge is missing glue, the pressure can be increased. If the pressure is high, the amount of glue will be high, but if the pressure is low, the amount of glue will be low.
下面说下针对某条边,或某个交,胶量不够的调试方法。在点击密封配方进入后会显示有向上密封,上部密封,向下密封,和下部密封,开始打胶的那条边就是向上密封,然后顺序从上。
Below is a debugging method for insufficient adhesive amount on a certain edge or intersection. After clicking on the sealing formula to enter, it will display up sealing, upper sealing, down sealing, and lower sealing. The edge where the glue starts is up sealing, and then the sequence starts from top.
如果先打胶的这条边,打胶不均匀,那么点击向上密封,进入后显示。扫描器开后发开的时间,就是在胶嘴贴到玻璃开始移动胶嘴出胶的时间,时间长出胶晚,时间短出胶早,扫描器开后开始移动的时间,就是胶嘴移动的速度,时间长移动慢,出胶多,时间短移动快出胶少。
If the edge where the glue is applied first is not evenly applied, click on "Seal Up" to enter the display. The time when the scanner is turned on is the time when the glue nozzle starts to move and release glue when it is pressed onto the glass. If the time is long, the glue will be released later, and if the time is short, the glue will be released earlier. The time when the scanner starts to move after turning on is the speed at which the glue nozzle moves. If the time is long, the movement will be slow, and the glue will be released more. If the time is short, the movement will be faster, and the glue will be released less.
扫描胶量细微调整,就是只有某条边胶少,或多,时调整扫描胶量细微调整,数值大胶量就大,数值小胶量就小。然后说下到末端伐关的距离,数值大,胶嘴到末端胶量少,数值小胶量大。
Fine adjustment of the scanning adhesive amount refers to adjusting the scanning adhesive amount when there is only a certain edge with less or more adhesive. If the numerical value is large, the adhesive amount will increase, and if the numerical value is small, the adhesive amount will decrease. Then, let's talk about the distance from the end of the gate. The numerical value is large, but the amount of glue from the nozzle to the end is small, and the numerical value is small, but the amount of glue is large.
本文由中空玻璃加工设备友情奉献.更多有关的知识请点击:http://www.jncsjx.com真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.
This article is dedicated to the friendship of insulating glass processing equipment. For more relevant knowledge, please click on: http://www.jncsjx.com Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned
上一篇:中空玻璃生产线在玻璃生产中发挥重要作用!
下一篇:铝合金门窗设备检验的内容有哪些?
相关新闻 moer+
- 中空玻璃生产线的磨损如何解决 2024/12/07
- 中空玻璃生产线的磨损如何解决 2024/12/07
- 玻璃涂布机设备:设备存在的安全隐患 2024/11/25
- 中空玻璃加工设备:玻璃开胶的应急处理措施 2024/11/21
- 中空玻璃生产线:玻璃起雾怎么办?昌盛为您解决! 2024/11/20
- 中空玻璃加工设备:选择中空玻璃,创更舒适的环境 2024/11/18
- 中空玻璃生产线的工艺流程 2024/11/16
- 全自动丁基胶涂布机的常见故障及解决方法 2024/11/13
- 中空玻璃的主要优缺点 2024/11/12
- 中空玻璃充气机的操作方法 2024/11/07