双组份涂胶机是生产中空、幕墙玻璃的专用设备，可一次完成二道密封中A、B组份混合与涂胶。适用配比精度高的胶种，满足玻璃深加工企业率、高合格率流水线作业的生产需求，是大规模生产高档中空玻璃及玻璃幕墙产品的一种理想的配套设备。
The two-component gluing machine is a special equipment for the production of hollow and curtain wall glass. It can complete the mixing and gluing of a and B components in the secondary seal at one time. It is an ideal matching equipment for large-scale production of high-quality insulating glass and glass curtain wall products.
双组份涂胶机由A、B胶泵、气动系统、升降机构、机架等组成。现分别介绍如下：
The two-component gluing machine is composed of a and B glue pumps, pneumatic system, lifting mechanism, frame, etc. It is introduced as follows:
1.胶泵：
1. Rubber pump:
（1）A、B组份各设一个胶泵，在各自的气马达驱动下，分别作往复运动，将胶吸入并压出。A、B胶泵分别与压胶盘固定在一起，再与机架连接组成各自的系统。

(1) Each component A and B is equipped with a glue pump. Driven by their respective air motors, they move reciprocally to suck in and press out the glue. A. The rubber pump B is fixed with the pressure plate respectively, and then connected with the frame to form their own system.
（2）A、B组份的配比是通过比例杠杆进行调节：向里调节，B出胶量减少，向外调节，B出胶量增加。通过调节比例杠杆来控制B胶的出胶量，从而控制A、B胶的配比。
(2) The proportion of component A and B is adjusted by the proportional lever: the amount of glue produced by b decreases when it is adjusted inward, but increases when it is adjusted outwards. By adjusting the proportion lever to control the glue output of glue B, the ratio of glue a and glue B can be controlled.
（3）出胶量：由气源处理器控制，逆时针调节，出胶量增加，顺时针调节出胶量减小。（这里指总出胶量）
(3) Glue output: controlled by the air source processor, it can be adjusted anticlockwise to increase the glue output and decrease the glue output by clockwise adjustment. (here refers to the total glue output)
本胶泵通过比例杠杆调节A、B胶量配比，具有操作灵活，性能稳定，调节范围大等特点。
The rubber pump adjusts the ratio of a and B glue through the proportional lever, which has the characteristics of flexible operation, stable performance and wide adjustment range.
2 . 升降机构：
2. Lifting mechanism:
A、B组份胶泵分别设一套气动升降机构，该升降机构分别由两个气缸并联组成，并通过横梁固定连接各自的泵体。其目的之一是将两缸的作用力通过压盘作用在胶面上，压力大小由调压阀调节，一般调整在0.3MPa左右；其二，当需要更换胶桶时，气缸可将压盘提起。离开胶桶，以便更换新的胶桶。
A. A set of pneumatic lifting mechanism is set for component B rubber pump. The lifting mechanism is composed of two cylinders in parallel, and the pump body is fixed and connected through the beam. One of the purposes is to apply the force of the two cylinders on the rubber surface through the pressure plate, and the pressure is regulated by the pressure regulating valve, which is generally adjusted at about 0.3MPa; the other is that when the rubber barrel needs to be replaced, the cylinder can lift the pressure plate. Leave the rubber barrel to replace it with a new one.