亮点：

Highlights:

1、采用双机油缸，配有大体积胶缸，可一次性装载14L丁基胶（2块正常的￠180mm的丁基胶）。

1. Adopting dual oil cylinders and equipped with large volume rubber cylinders, it can load 14L of butyl rubber (2 pieces of normal ￠ 180mm butyl rubber) at once.

2、增压系统的主泵采用德国原装进口麦格思维特（MAXIMATOK）的增压泵。

2. The main pump of the boosting system adopts the German imported MAXIMATOK boosting pump.

主要性能特点:

Main performance characteristics:

1、该机为半自动涂布机（即人工扶持间隔框进行逐边操作）,变频调速。

1. This machine is a semi-automatic coating machine (i.e. manually supporting the interval frame for edge by edge operation), with variable frequency speed regulation.

2、将间隔框放在传送带上人工扶持框传送带运行，通过传感器时，传送压轮及打胶阀按设定程序自动动作。

2. Place the spacer frame on the conveyor belt and manually support it to run. When passing through the sensor, the conveyor pressure wheel and glue valve will automatically operate according to the set program.

3、摆动气缸动作、压轮压下，压送铝间隔框行进，当间隔框到达打胶头时打胶，将胶均匀地涂在铝间隔框上。

3. Swing the cylinder and press down the pressure wheel to push the aluminum spacer frame forward. When the spacer frame reaches the glue head, apply glue evenly to the aluminum spacer frame.

4、等间隔框另一侧快要到达压轮时，压轮抬起，离开打胶头时，胶阀自动关闭，停止打胶，以上程序由PC控制，时间有人机界面控制，可以触摸调节。

4. When the other side of the equidistant box is about to reach the pressure wheel, the pressure wheel lifts up and leaves the glue head. The glue valve automatically closes and stops gluing. The above program is controlled by a PC, and the time is controlled by the human-machine interface, which can be adjusted by touch.

5、在设计、选用元气件以及涂胶效果方面，在国内均属水平。

5. In terms of design, selection of components, and coating effect, it is at the same level in China.

6、采用PC控制系统，定位、传送、涂胶均自动完成。

6. Using a PC control system, positioning, conveying, and gluing are all automatically completed.

7、输送采用变频调速电机调速，运行速度平稳。

7. The conveyor adopts variable frequency speed control motor for speed regulation, and the running speed is stable.

8、有不泄压即可自动调定位机构，充分保证涂胶胶头与隔框两侧间距涂胶均匀。

8. There is an automatic positioning mechanism that can be adjusted without pressure relief, fully ensuring that the adhesive head and the distance between the two sides of the partition frame are evenly coated.

主要技术参数：

Main technical parameters:

挤胶压力:12-14Mpa

Squeezing pressure: 12-14Mpa

电源:380V

Power supply: 380V

打胶温度:100-140度

Glue temperature: 100-140 degrees Celsius

总功率: 2.5Kw

Total power: 2.5Kw

气动压力:0.5-0.8Mpa

Pneumatic pressure: 0.5-0.8Mpa

胶头可调范围:4-20mm

Adjustable range of adhesive head: 4-20mm

打胶速度:22米/分钟

Glue application speed: 22 meters per minute

外形尺寸:3000*700*1236mm

Dimensions: 3000 * 700 * 1236mm

总重量:850kg

Total weight: 850kg