
丁基胶涂布机温控表温度的调整技巧
时间:2018-01-22 来源:http://www.jncsjx.com/ 发布人:昌盛机械
丁基胶涂布机是完成中空玻璃首道密封的必备设备之一,所起到的作用无可替代,所以也是中空玻璃制作厂家必备设备之一,那么我们就谈一下它的保养与维修,
Butyl rubber coating machine is one of the necessary equipment to complete the first hollow glass sealing, the irreplaceable role played, so it is one of the necessary equipment of insulating glass production factory, then we will talk about the maintenance and repair,
出胶比不均匀,调节胶头上的顶丝,二是胶缸不进不退,气动的考虑是气动阀卡了(要常加油)液压的就是液压站油泵漏气,或者是油缸内泄漏(压力升一点马上降下来)三是胶头出胶很不匀,一边粘的很好,另一边不粘,就是一侧加热棒坏了,或者线头断了。
A binder ratio is not uniform, regulating screw plastic head, two is a rubber cylinder irreversible, pneumatic pneumatic valve is considered card (often to refuel) is the hydraulic station hydraulic oil pump leak, or cylinder leakage (pressure rise a little down immediately) three is plastic head the glue is not uniform, while the viscosity is very good, the other side is the side of the heating rod is not sticky, broken, or broken head.
检查胶缸、胶头的温度是否正常,压力是否在我们设定的范围之内,检查两胶头的距离是否过大(此距离设定至铝条刚刚能从两个打胶头之间过去为好)。

Check whether the temperature of the rubber cylinder and rubber head is normal, whether the pressure is within our range, and check whether the distance between the two rubber heads is too large (the distance is set to the aluminum strip just to pass from the two rubber heads to the best).
该设备的胶头加热和胶缸加热,由加热棒两个和加热盘一个提供,由温控表来设定和调整温度的高低,若发现温度升不高或升高后往下降,请检查加热棒或加热盘是否损坏,并检查温控表是否正常。
The device of glue and glue cylinder head heating heating, a heating rod two and a heating plate, a temperature control table to set and adjust the temperature, if the temperature rise is not high or increased after going down, please check the heating rod or the heating disc is damaged, and check whether the normal temperature table.
该设备全部采用液压系统,油缸及液压系统全部采用高压油管连接,每个连接处都由组合垫密封,若发现漏油,及时更换组合垫。
The device adopts hydraulic system, oil cylinder and hydraulic system are all connected by high pressure oil pipe. Each connection is sealed by combination gasket. If we find oil leakage, replace the combination cushion in time.
皮带跑偏,调节平衡螺杆。六是胶头朵堵了,卸下来,用汽油 洗干净清理脏东西,再安上,以后加胶注意不要沾上脏东西。中空玻璃设备
The belt runs off and regulates the balance screw. Six is glue head plugging, unloaded, clean clean dirty things with gasoline, and then go up, add glue and pay attention not to dirty things later. Hollow glass equipment
本文由双组份打胶机友情奉献.更多有关的知识请点击:http://linshi.jncsjx.com我们将用的技术.真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.
This article is a friendship contribution from two component glue making machine. Please click on more related knowledge: http://linshi.jncsjx.com, we will use the most advanced technology and the most sincere attitude to provide you with the most comprehensive service. We will dedicate more related knowledge to you. Please look forward to it.
- 中空玻璃生产线打胶机传送V带不平衡?这样调,传送平稳不跑偏 2026/02/13
- 中空玻璃生产线打胶难题:压力够却打不满胶?这样排查就解决 2026/02/12
- 全自动封胶线实操科普:山东昌盛板压段,筑牢封胶质量核心防线 2026/02/10
- 中空玻璃生产线实操科普:小玻璃清洗机反转打滚?这样解决最省心 2026/02/06
- 全自动封胶线实操科普:白胶泵密封圈这样换,杜绝漏胶保顺畅 2026/02/04
- 双组份打胶机实操科普:出胶体这样保养维护,延长寿命保顺畅 2026/02/02
- 中空玻璃生产线:清洗机这样保养,清洁高效更耐用 2026/01/30
- 全自动封胶线实操科普:板压压合效果差?四角落差这样调精准 2026/01/28
- 双组份打胶机实操科普:黑胶泵过滤这样清洗,避免堵塞保顺畅 2026/01/27
- 中空玻璃丁基胶涂布机突发停电?这样清洗胶枪,次日正常开工 2026/01/23

当前位置:



产品分类Product categories
联系我们Contact us
