1、固化速度太快或太慢

　　1, curing speed is too fast or too slow

　　2、双组份打胶机混合不匀，出现白丝，花胶

　　2, two-component glue mixing is not uniform, white silk, fish maw

　　①打胶机混合器单向阀泄漏，更换单向阀。

　　Rubber mixer, mixer one-way valve leakage, replace one-way valve.

　　②打胶机混合器及枪内通道部分堵塞，清洗混合器和管道。

　　The glue mixer, mixer and gun passages are blocked, and the mixer and pipe are cleaned.

　　③打胶机比例泵内有脏物，清洗比例泵。

　　There is dirt in proportion pump and cleaning proportion pump.

　　④空压机空气压力不足，气量不稳，调整压力。

　　The air pressure of the air compressor is not enough, the air volume is unstable, and the pressure is adjusted.

　　3、打胶机压盘冒胶

　　3, glue machine, pressure plate gel

　　①压盘密封圈损坏变形，老化发硬，更换新的胶圈。

　　The sealing ring of pressure plate is damaged, deformed, aged and hard to be replaced, and new rubber ring is replaced.

　　②升降压力太大。

　　The lifting pressure is too great.

　　③桶太大了，不合适，客户在采购时，先量一下自己的打胶机压盘大小，现在市面上机器压盘有三个规格的，560mm，565mm，571mm,暖万佳科技开发有限公司可以跟据客户的机器压盘大小，提供相应的包装桶包装。

　　The barrel is too big, not appropriate, customers in the procurement, the first volume of your gum machine platen size, now on the market of machine platen three specifications, 560mm, 565mm, 571mm, warm Wanjia science and technology development limited company can according to customer's machine platen size, provide the corresponding packaging barrels packaging.

　　4、中空玻璃安装，经冷、热交换起雾的问题

　　4, the installation of insulating glass, cold and heat exchange fog

　　①双组份硅酮胶主要是二道密封，粘结结构的作用，所以头道密封必须用丁基密封胶密封，插角处用丁基胶密封完全。

　　The two-component silicone rubber is mainly two sealing, bonding structure, so the seal must be sealed with butyl sealant, inserted at the corner completely sealed with butyl rubber.

　　②高温、高湿季节，必须用质量较好的分子筛，完全能够将玻璃密封后残存的湿气吸干净，以绝后患。整个操作时间不能太久。

　　In the season of high temperature and high humidity, must use the better quality of the molecular sieve can be completely sealed after the remaining moisture glass suction clean, with all. The whole operation shouldn't take long.

　　5、胶盘压不下去

　　5, rubber disc pressure can not go down

　　①桶变形，不圆了，可用锤子把桶口拷圆，再压下去。

　　The barrel deformation, not round, available hammer bungholes copy circle, press down.

　　②桶太小了，或是压盘密封圈过大，可以在密封圈上涂抹一点白胶，可起到润滑的作用再压下去。

　　The barrel is too small, or the pressure plate sealing ring is too large, you can smear a little glue on the sealing ring, can play the role of lubrication pressure.

　　6、气泡问题(A组份有气泡或是混合后出现气泡)

　　6, bubble problem (A group has bubbles or bubbles after mixing)

　　①压胶时未能完全排尽空气，所以每次换胶时，一定要把排空气的阀门打开，等空气排完后再关上。

　　Pressure glue can not completely exhaust the air, so every time you change glue, you must open the exhaust valve, and then close the air after the completion of the switch.

　　②手动混胶过程中混入空气。

　　Mixing air in manual mixing process.

　　本文的精彩内容来自双组份打胶机详细内容请点击我们的官方网站:http://linshi.jncsjx.com/谢谢您的到来!

　　The exciting content of this article comes from the two component dispenser, please click on our official website: http://linshi.jncsjx.com/, thank you for coming!