双组份打胶机在使用过程中需要遵循什么?

发布时间:2020/06/23    发布人:

1、真空回吸阀必需要安装在全自动点胶机上,由于真空回吸功能是避免点胶机中的胶水在不点胶时还在滴漏。
1. The vacuum suction valve must be installed on the automatic dispenser, because the vacuum suction function is to prevent the glue in the dispenser from leaking when it is not dispensing.
2、点胶量的大小是由全自动双组份打胶机在点胶进程中继续的时刻长短来抉择的,可以保证有满足的胶水来粘合部件,一起可以避免胶水过多而造成的资源浪费。
2. The size of dispensing volume is determined by the duration of the full-automatic two-component dispenser in the dispensing process. It can ensure that there is enough glue to glue the parts, and it can avoid the waste of resources caused by too much glue.
3、在全自动双组份打胶机职业中一般运用的胶水大概有硅胶、瞬间胶、厌氧胶、环氧树脂、UV胶。
3. The general glue used in the full-automatic two-component gluing machine industry is about silica gel, instant glue, anaerobic glue, epoxy resin and UV glue.
4、针头的规范与类别:针头的规范会影响点胶机在点胶进程中出胶的大小和精密度,当气压在必定规模时,针头的咀越大,出胶率就越大,所以要根据点胶机在出产出来产品的大小来定位点胶针头的规范,一般针头内径长度保持在胶点直径的一半,作用才是最好。
4. Specification and category of needle: the specification of needle will affect the size and precision of dispensing machine in the dispensing process. When the air pressure is at a certain scale, the larger the tip is, the larger the dispensing rate is. Therefore, the specification of dispensing needle should be positioned according to the size of the products produced by the dispensing machine. Generally, the length of the inner diameter of the needle is kept at half of the diameter of the dispensing point, which is the best.


5、固化要素:关于胶水的固化,一般出产厂家已给出温度曲线。一般在常温下都可以固化,在实际应尽可能选用较高温度来固化,使胶水固化后有满足强度和硬度。
5. Curing factors: for the curing of glue, the general manufacturer has given the temperature curve. Generally, it can be cured at room temperature. In practice, higher temperature should be selected as far as possible to make the glue meet the strength and hardness after curing.
6、气泡关于全自动双组份打胶机在进行点胶进程中会影响产品质量,所以胶水放进去之前决对不能有气泡.如果有气泡就会造成点胶机出产出来的产品有许多次品,在运用中要排出胶水的空气,以避免呈现全自动点胶机空打现象。
6. Bubble about the automatic two-component dispenser will affect the product quality in the dispensing process, so there must be no bubble before the glue is put in. If there is bubble, there will be many defective products produced by the dispenser, and the air of the glue should be discharged during the application, so as to avoid the phenomenon of empty dispensing of the automatic dispenser.
7、压力的大小直接影响了供胶量和胶水流出的速度,胶水的流动性越差它就越稠,全自动双组份打胶机需求的压力就越大,所以咱们应该根据全自动点胶机在出产进程中的环境温度以及点胶量的大小和胶水的特性来调度压力的大小,全自动点胶机的压力大小是经过它内部的调压阀来进行调度的。
7. The pressure directly affects the glue supply and the speed of glue outflow, The worse the fluidity of glue, the thicker it will be, and the greater the pressure required by the full-automatic two-component dispenser. Therefore, we should adjust the pressure according to the ambient temperature of the full-automatic dispenser in the production process, the size of the dispensing amount and the characteristics of glue. The pressure of the full-automatic dispenser is regulated by its internal pressure regulating valve.
以上就是双组份打胶机为大家做介绍的在使用过程中需要遵循什么? 想要了解更多的双组份打胶机的内容  请关注官网http://www.jncsjx.com
The above is the double beater for you to do the introduction in the use process to follow what? To learn more about the duplicator, please pay attention to the official website http://www.jncsjx.com