双组份打胶机不可忽视的日常保养都有哪些方面?

发布时间:2020/03/20    发布人:

  双组份上胶机控制系统采用PLC和触摸屏,人机界面,一键操作。该设备操作简单,使用方便。伺服控制系统选用世界名牌(日本安川),功能更稳定。满足设备运行要求,玻璃污染可忽略不计。只需一人操作设备即可完成整块玻璃的上胶。稳定可靠,生产效率高。双组份涂胶机由A、B胶泵、气动系统、升降结构、机架等组成。那么在使用双组份胶机时注意什么问题呢?让我们来了解一下。
  The control system of two-component gluing machine adopts PLC and touch screen, human-machine interface and one key operation. The device is easy to operate and use. The servo control system adopts the world famous brand (Yaskawa, Japan), with more stable function. Meet the operation requirements of the equipment, and the glass pollution can be ignored. It only needs one person to operate the equipment to complete the gluing of the whole glass. Stable and reliable, high production efficiency. The two-component glue applicator consists of a and B glue pumps, pneumatic system, lifting structure, frame, etc. So what should we pay attention to when using the two-component glue machine? Let's understand.
  1. 由于双组份制胶机的固化需要一定的时间,所以涂有双组份密封剂的玻璃需要水平移动。
  1. Since the curing of the two-component glue making machine takes a certain time, the glass coated with the two-component sealant needs to move horizontally.
  2. A组和B组的胶要保持清洁,严禁异物进入胶内。

双组份打胶机
  2. The glue of group A and group B shall be kept clean and no foreign matters are allowed to enter into the glue.
  3.连续运行过程中,胶枪停止时间不超过20分钟。否则,应使用胶水的组成部分冲洗所有混合的胶水,直到一个单一的组成部分的胶水从枪口排出。
  3. During continuous operation, the stop time of glue gun shall not exceed 20 minutes. Otherwise, all mixed glue should be rinsed with a component of glue until a single component of glue is discharged from the muzzle.
  4. 不得强行挤压或弯曲高压软管,以免影响系统的正常运行。
  4. Do not squeeze or bend the high-pressure hose forcibly to avoid affecting the normal operation of the system.
  5. 混合器应始终保持畅通,以确保良好的粘合剂效果。若堵塞,浸泡后用丙酮冲洗。建议每5套洗一次。
  5. The mixer shall be kept smooth at all times to ensure good adhesive effect. If clogged, wash with acetone after soaking. It is recommended to wash every 5 sets.
  6. 当胶枪长时间不使用(超过一周)时,应将胶枪本体取出,用溶剂清洗胶枪和混合器内残留的凝胶。
  6. when the rubber gun is not used for long time (over a week), the rubber gun body should be removed and the residual gel in the rubber gun and mixer should be cleaned with solvent.
  7. 不同双组分打浆机生产的胶中杂质的含量不同。根据实际情况,B组件的滤网和单向止回阀每两组清洗一次。
  7. The content of impurities in the rubber produced by different two-component beaters is different. According to the actual situation, the filter screen and check valve of B assembly shall be cleaned once every two groups.
  8. 由于胶枪、管道或机器的胶态固化而造成的任何缺陷都不在保修范围内。
  8. Any defects caused by the glue curing of glue gun, pipe or machine are not covered by the warranty.
  9. 定期向双组份打浆机各泵的加油口加注油,保证油在雾化器内持续存在。
  9. Regularly add oil to the oil filler of each pump of the two-component beater to ensure the continuous existence of oil in the atomizer.
  以上就是对双组份打胶机注意事项的详细介绍,想要了解更多请点击官网http://www.jncsjx.com
  The above is a detailed introduction to the precautions of the two-component dispenser. For more information, please click http://www.jncsjx.com