双组份打胶机的注意事项!

发布时间:2019/09/27    发布人:

双组份打胶机采用无触点电器控制系统控制,换向灵敏可靠,其独特的方便可调试配比机构,大限度地保证双组份胶近乎苛刻的配比要求,出胶连续均匀,涂胶效果好,生产效率高。今天小编给大家总结一下双组份打胶机的注意事项,希望对大家有所帮助!
The two-component glue beater is controlled by contactless electrical control system, which is sensitive and reliable in reversing direction. Its unique convenient and adjustable proportioning mechanism ensures that the two-component glue meets the strict proportioning requirements to a great extent. The glue is produced continuously and evenly, the glue effect is good, and the production efficiency is high. Today, Xiaobian summarizes the matters needing attention of the two-component glue punch, hoping to be helpful to you all! 
1.由于双组份密封胶的固化需要一定时间,因此双组份打胶机,已涂了双组份密封胶的玻璃应水平轻轻搬动。A组、B组份胶应保持清洁,严防异物进入胶中。
1. Since the curing of two-component sealant takes some time, the glass coated with two-component sealant should be moved horizontally and gently. Group A and B glue should be kept clean and foreign bodies should be strictly prevented from entering the glue.
2.不同双组份胶生产厂家所生产的胶内含杂质数量不同,根据实际情况清晰B组分的过滤网及单向止回阀,建议每两组清洗一次
2. The amount of impurities in the glue produced by different two-component glue manufacturers is different. According to the actual situation, the filter screen and check valve with clear B component are recommended to be cleaned once for each two groups.
3.如遇堵塞情况,可用丙酮浸泡后清洗。建议每5组清洗一次。
3. In case of blockage, it can be soaked in acetone and cleaned. It is recommended to clean every 5 groups.

双组份打胶机
4.当胶枪长时间不用时(超过一周),应拆下枪体使用溶剂将胶枪和混胶器内的残留胶体清洗干净。
4. When the rubber gun is not used for a long time (more than a week), the gun body should be removed and the residual colloid in the rubber gun and mixer should be cleaned with solvent.
5.混胶器应经常保持畅通,以保证良好的出胶效果。
5. Mixers should be kept unblocked regularly to ensure good gumming effect.
6.高压胶管不得强行挤压、弯曲,防止影响系统正常工作。
6. High-pressure hose shall not be forced to extrude or bend to prevent the normal operation of the system.
7.在连续工作过程中,胶枪每次停止工作时间一般不得超过20分钟,否则,应用A组份胶冲出全部混合胶,直至单一的A组份胶从枪口排出为止。
7. In the continuous working process, the rubber gun should not stop working for more than 20 minutes at a time. Otherwise, the whole mixture should be produced by using component A glue until a single component A glue is discharged from the muzzle of the gun.
今天给大家介绍的精彩内容到这里就结束了,小编在这里十分感谢大家的阅读,如果大家想要了解更多的相关咨询,可以把我们的网址:http://www.jncsjx.com添加到收藏,或者搜索关键词:双组份打胶机,也可以找到我们。
Today's wonderful content for you is over. The edition here is very grateful for your reading. If you want to know more about the relevant consultation, you can add our website: http://www.jncsjx.com to the collection, or search keywords: two-component glue machine, you can also find us.