中空玻璃打胶机的使用技巧

发布时间:2022/08/26    发布人:

中空玻璃打胶机在使用过程中或者停止时,会出现一些玻璃渣,原因是:胶嘴护套损坏,铝槽深度检测探头行走划到了玻璃,挡胶板或者刮胶板的前进力量太大。解决方法:重新换护套,调整探头位置,让探头在铝槽中间行走。调节前进气缸的速度到合适,可以避免出现玻璃渣。
During the use or stop of the insulating glass gluing machine, there will be some glass slag. The reasons are: the rubber nozzle sheath is damaged, the aluminum groove depth detection probe moves and scratches the glass, and the forward force of the rubber baffle or the rubber scraper is too large. Solution: replace the sheath, adjust the position of the probe, and let the probe walk in the middle of the aluminum tank. Adjusting the speed of the forward cylinder to an appropriate value can avoid the occurrence of glass slag.
打胶的过程中,有时候还没打完就开始后面的动作,这样是很不好的,很容易损害玻璃,出现这种情况的原因:可能是因为机头前面的光纤头有遮挡物,或者可能是光纤头螺母松动或倾斜。或者是表面有脏东西,或者是检测的距离太小,行走时有波动,影响检测。解决方法:清洗光纤头,或者是固定好,或是清理玻璃表面,调整至合适的检测距离。
In the process of gluing, sometimes the following actions are started before the gluing is finished. This is very bad and it is easy to damage the glass. The reason for this situation is that the optical fiber head in front of the machine head is blocked, or the nut of the optical fiber head is loose or inclined. Either there is dirt on the surface, or the detection distance is too small, and there is fluctuation when walking, which affects the detection. Solution: clean the optical fiber head, or fix it, or clean the glass surface, and adjust it to the appropriate detection distance.
运转过程中总是有些不协调,各个动作之间不协调,出现原因:参数设置有误,需重新设置参数。如果是气动系统配件老化的话,就换一个新的。
There is always some incongruity in the operation process, and there is incongruity between various actions. The reason for this is: the parameter setting is wrong, and the parameter needs to be reset. If the pneumatic system parts are aging, replace them with new ones.


电机不稳定,时快时慢。原因:铝槽不直,导轨不直或是滑动轴承损坏。
The motor is unstable, fast and slow. Cause: the aluminum groove is not straight, the guide rail is not straight or the sliding bearing is damaged.
中空玻璃打胶机主要是用于中空玻璃的密封,所以说中空玻璃的性能完全看中空玻璃打胶机。可是因为施工人员对机器的不够了解,因此有时候打胶的结果不是很好,所以关于中空玻璃打胶机的具体操作注意的地方就很重要了。在清洗混胶器、胶嘴或混胶的时候,要把机头划至轨道的末尾,还要用胶板接住胶嘴流出来的胶,以防设备被污染。此外,打胶机在出厂时都有固定的参数,这个就是为了不懂得用户来设计的。就算自己什么都懂了,也不要轻易的修改参数。在调整参数时,根据自己需要的参数设定,千万不可随意设定参数,以免控制器发出错误的信息,影响到打胶的质量、工程的进度,更有甚者会损毁设备。在冲洗混胶器、胶嘴或者混胶时,一定要先打开胶嘴控制的阀门,之后在打开供胶机。这个顺序一定要记住。这是避免压力剧增损坏设备或者出现安全事故。
The insulating glass gluing machine is mainly used for sealing the insulating glass, so the performance of the insulating glass depends entirely on the insulating glass gluing machine. However, because the construction personnel do not know enough about the machine, sometimes the results of gluing are not very good, so it is very important to pay attention to the specific operation of the insulating glass gluing machine. When cleaning the rubber mixer, rubber nozzle or mixing, draw the head to the end of the track, and use a rubber plate to catch the glue flowing out of the rubber nozzle to prevent the equipment from being polluted. In addition, the gluing machine has fixed parameters when it leaves the factory, which is designed for users who do not know. Even if you know everything, don't modify the parameters easily. When adjusting the parameters, set the parameters according to your own needs. Do not set the parameters at will, so as to prevent the controller from sending wrong information, affecting the quality of gluing and the progress of the project, and even damaging the equipment. When flushing the glue mixer, glue nozzle or glue mixing, be sure to open the valve controlled by the glue nozzle first, and then open the glue feeder. This order must be remembered. This is to avoid damage to equipment or safety accidents caused by pressure surge.
以上就是为大家介绍的有关中空玻璃生产线的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.jncsjx.com
The above is the detailed introduction of the insulating glass production line for you. I hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with an attitude of http://www.jncsjx.com